
A frequency chart tells you what exists. It does not tell you what to use. Many new and returning operators can find a table of amateur bands in seconds, then still wonder where to tune for a first local contact, a long-distance voice QSO, or a plan for emergencies. The answer depends on who you are, what you want to do, and what your station can handle.
This guide works through four filters, in order: legal privileges, the band plan and local etiquette, propagation and time of day, and equipment limits. It is written for operators in the United States. Operators in IARU Region 1 (Europe, Africa, Middle East) and Region 3 (much of Asia and the Pacific) work under different national rules and band plans, so check your own national regulator and regional plan.
One principle runs through everything below: learn where to verify limits rather than memorizing numbers. Rules, band plans, and local repeater arrangements change, and a copied table may be out of date.
Start With Rules, Not Charts: What Actually Limits Where You Can Transmit
Frequency privileges vs. the band plan
Two different things get mixed up constantly:
- Frequency privileges are legal. They come from the FCC's Part 97 rules and determine which parts of which bands your license class may use, with which emission types, and at what power.
- Band plans are voluntary. They are agreements among operators, such as the ARRL band plan and local coordination, about how to share space so that different activities do not collide.
You can be completely legal and still be a poor neighbor, for example by holding a long chat on a frequency used for calling. You can also follow a band plan faithfully and still break the law if you transmit outside your license privileges. You need to satisfy both.
How license class affects access
In the US, the three license classes are Technician, General, and Amateur Extra. In broad terms, Technician privileges center on VHF and UHF with limited HF access, General opens up substantial HF privileges, and Amateur Extra covers all amateur allocations. Do not rely on that summary for real operating decisions. Exact band edges, sub-bands, and conditions are set out in 47 CFR 97.301 through 97.305, and these sections are the authority. A table copied onto a forum or a printed chart may be outdated or contain errors.
Also remember that some segments carry conditions, such as shared allocations with other services. Part 97.303 addresses frequency sharing requirements, so you should know which of your bands are shared and what that implies.
Mode segments and emission rules
A frequency can be legal for one mode and not for another. Part 97.305 lists authorized emission types by band segment, and Part 97.307 sets emission standards. Practically, this means a segment may be limited to CW and certain digital modes while another allows voice. Before you transmit on a new mode in a new place, confirm that the mode is authorized on that exact frequency for your license class. Operating in the right band but the wrong segment is a classic way for new HF operators to run afoul of the rules.
Obligations that apply on every frequency
No matter where you tune, some responsibilities travel with you:
- Identification (97.119): You must identify with your call sign, generally at the end of a communication and at regular intervals during it. Check the rule for the exact timing and permitted methods.
- No interference and sharing: You must not cause harmful interference, and you should always listen before transmitting.
- Prohibited transmissions (97.113): This covers things like business communications on behalf of an employer, music, obscene or indecent language, and certain other content. Read the section rather than guess.
- Good amateur practice (97.101): The rules expect operators to follow good engineering and operating standards, including using the minimum power needed for the communication.
Filter One: Pick the Band by What You Want to Accomplish
Once you know what you are permitted to do, narrow things by goal.
Local conversations and nets: 2 m and 70 cm FM
For talking with people in your area, the 2 meter (144 to 148 MHz) and 70 centimeter (420 to 450 MHz) bands are the usual starting point. FM voice is simple, handhelds are inexpensive and portable, and most local clubs run repeaters and nets there. If you are a new Technician, this is likely where you will spend your first weeks.
Regional and long-distance contacts: HF
The HF bands (roughly 3 to 30 MHz) can support contacts across states and around the world, because signals can be refracted by the ionosphere. In general terms, lower HF bands such as 80 and 40 meters tend to be more useful at night and for regional work, while higher bands such as 15, 12, and 10 meters depend more heavily on solar conditions and tend to be better in daylight when they are open at all. These are general patterns, not promises. Conditions vary by day, season, and the solar cycle.
Weak-signal and experimental work
The 6 meter band and above include segments dedicated to SSB, CW, and weak-signal digital modes, separate from FM repeaters and simplex. These segments reward patience, good antennas, and attention to the band plan. Calling on an FM channel when you want weak-signal contacts will not get you far, and FM operators do not belong in the weak-signal portion.
Satellites and the ISS
Amateur satellites and ISS amateur radio activity use specific frequencies and often specific modes, but operating status changes. A satellite may be in a limited mode, a transponder may be off, or a pass may be reserved for a scheduled event. Before transmitting, check current information from AMSAT or ARISS rather than relying on a frequency you saw in an old article. Transmitting to a satellite that is not operating wastes your time and may cause interference.
Emergency communications
There is no universal, magic emergency frequency for amateurs to rely on. What you should use is the plan in your area. That may involve ARES or RACES groups, agreements with served agencies, and designated repeaters and simplex channels. A national calling frequency is not an emergency channel, and guessing leads to confusion. If you want to be useful in a crisis, join your local group, learn its plan, and practice with it before you need it.
Filter Two: Reading a Band Plan Like an Operator
Where to find the current plan
Use the ARRL band plan for US operating conventions, your IARU regional plan if you are outside the US, and local frequency coordinators for repeater pairs. Because coordination is regional, a repeater directory that is not kept current can be misleading. Treat any list as a starting point and confirm with the repeater owner or a local club.
Common conventions
Two stable examples illustrate how a band plan works in practice:
- 146.520 MHz is the national FM simplex calling frequency on 2 meters in the US.
- 446.000 MHz is the national FM simplex calling frequency on 70 centimeters.
A calling frequency is where you make contact, not where you stay. The usual practice is to say who you are, make contact, and then agree on another simplex frequency to move to so the calling channel remains clear for others. Long conversations on a calling frequency are poor etiquette.
Repeater basics
A repeater receives on one frequency (its input) and retransmits on another (its output). Your radio transmits on the input and listens on the output, so you need to set the offset correctly, and often a CTCSS (PL) tone as well. Common US conventions are an offset of 600 kHz on 2 meters and 5 MHz on 70 centimeters, with direction (plus or minus) depending on the part of the band and local practice. Conventions vary by region, and some repeaters use nonstandard pairs or tones. Always check the current listing or ask the owner. Some repeaters are also closed or restricted, so confirm that you are welcome to use one.
Avoiding stepping on others
- Listen first. Spend a minute or more before transmitting, especially on HF where you may not hear both sides of a conversation.
- Ask. Say, "Is this frequency in use?" and give your call sign. Wait for a response.
- Respect beacons, nets, and weak-signal segments. Many are quiet most of the time but active at scheduled times.
Filter Three: Match Frequency to Propagation and Time of Day
VHF and UHF
On 2 meters and 70 centimeters, signals typically travel line of sight, so antenna height and terrain matter more than time of day. A handheld inside a building may only reach the nearest repeater, while the same radio on a hilltop with a better antenna might reach much farther. Occasionally, tropospheric enhancement can extend range far beyond normal. It is unpredictable, so treat it as a bonus and not a plan.
HF
HF behavior depends on the ionosphere, which changes with time of day, season, and solar activity. Instead of asserting what is open right now, use live tools:
- Beacon networks that transmit on known frequencies so you can see what you can hear.
- Reporting sites that show where recent digital signals were received.
- Published solar indices and propagation forecasts to understand general trends.
These tools tell you what is happening now, which beats any static table.
A simple order for a new HF operator
- Listen. Tune within your privileges and see which bands have activity.
- Check reports. Look at live reporting tools to see whether signals are being heard in the direction you want.
- Call. Answer a CQ first if you are nervous, or call CQ in an appropriate segment after confirming it is clear.
Filter Four: Make Sure Your Equipment Fits the Frequency
Antenna resonance and SWR
An antenna is designed for particular frequencies. A good 2 meter antenna may do almost nothing useful on 40 meters, and trying to transmit through a badly mismatched antenna can stress your radio and waste power. Check SWR, use an antenna designed for the band, and tune within the range the antenna supports.
Power limits and amplifiers
Part 97.313 sets legal maximum power limits and requires you to use the minimum power necessary for the communication. Legal maximum is not the same as what is necessary or courteous. Many contacts are made with modest power, and adding an amplifier will not fix a poor antenna. If you do use an amplifier, make sure it is operated properly and that you understand your rules and any local interference concerns.
Radio capabilities
Know what your radio can do: which bands it transmits on, whether it supports SSB, FM, and digital modes, and how it handles filtering. Some radios, especially inexpensive ones or those with unlocked transmit ranges, can transmit outside the amateur bands. Just because a radio will key up on a frequency does not mean you are allowed to use it. Scanner-style programming can make it easy to put a non-amateur frequency in a memory by mistake.
Handheld programming pitfalls
The most common programming errors are the wrong offset, the wrong or missing tone, and the wrong bandwidth (wide vs. narrow). Before relying on a repeater, test your handheld on simplex with another ham or listen carefully to confirm you have the right output. Then add the repeater, check your offset and tone against a current listing, and make a brief call sign check-in.
Worked Examples: From Goal to Frequency
New Technician, first local contact
- Confirm your Technician privileges on 2 meters and 70 centimeters in 47 CFR 97.301 and 97.305.
- Find local repeaters in a current directory or on a club website. Note output, offset, tone, and any access rules.
- Program your handheld and double-check offset and tone.
- Listen for activity. When there is a pause, give your call sign and say you are new and listening.
- If you want a simplex contact, call on 146.520 MHz, then move to another simplex frequency after you connect.
Newly upgraded General wanting an HF voice contact
- Check your new General privileges and which segments permit voice. Verify in Part 97 rather than trusting a pocket chart.
- Choose a band that suits your time of day and goals, and confirm your antenna works there with an acceptable SWR.
- Listen. Check live reporting or beacon tools to see what is open.
- Answer a CQ or call after asking whether the frequency is in use.
- Identify properly and keep power reasonable.
Emergency-prep operator building a local communications plan
- Contact your local ARES or RACES group or club to learn which repeaters and simplex channels the community uses.
- Write down primary and backup frequencies, offsets, and tones, and note who maintains them.
- Test your equipment on those channels and practice regularly in nets.
- Keep a printed copy, and review it periodically because coordination can change.
Quick Verification Checklist Before You Key the Mic
- Is the frequency within my license class privileges?
- Am I inside the correct band edges and sub-band?
- Is my mode allowed on this segment?
- What does the current band plan say about this frequency?
- If it is a repeater, have I confirmed the offset, tone, and access policy?
- Does my antenna work on this band, and is SWR acceptable?
- Am I using only the power I need?
- Have I listened and asked whether the frequency is in use?
- Am I ready to identify properly?
Common Mistakes and How to Avoid Them
- Treating a chart as complete or current. Verify against Part 97 and the current band plan.
- Ignoring regional differences. Band plans, repeater conventions, and rules differ by country and sometimes by area.
- Using a repeater output as simplex. Transmitting on a repeater's output can interfere with the repeater's transmissions.
- Holding long chats on a calling frequency. Make contact and move.
- Assuming propagation is the same every day. Check live tools and be flexible.
Where to Go Next
- FCC Part 97 in the eCFR for the authoritative rules.
- ARRL band plans and frequency charts for US conventions.
- IARU regional plans if you operate outside the US.
- Local repeater coordinators for current repeater information.
- Local clubs and Elmers for practical, area-specific guidance.
Frequently Asked Questions
Can I transmit on any frequency I can tune?
No. Being able to tune a frequency says nothing about whether you may transmit there. Your license privileges and the rules for the band and mode control that.
Is a band plan law?
No, band plans are voluntary agreements. However, following them is part of good amateur practice, and ignoring them often causes interference. Legal limits, by contrast, come from Part 97.
What are simplex frequencies?
Simplex means both stations transmit and receive on the same frequency, without a repeater. It is used for direct station-to-station contact.
Do repeater offsets vary?
Yes. Common conventions exist, such as 600 kHz on 2 meters and 5 MHz on 70 centimeters in the US, but the direction and exceptions vary by region and by repeater, so always check a current listing.
What is a calling frequency?
A calling frequency is a frequency where operators make initial contact, such as 146.520 MHz on 2 meters. After you connect, move to another frequency so that others can use it to call.
Conclusion
Choosing a frequency is a sequence of decisions: first, what the law lets you do; second, what the band plan and local etiquette ask of you; third, what propagation will support; and fourth, what your equipment can actually deliver. Work through those four filters and a long chart becomes a short list of workable options. Before you transmit, confirm the current rules, the current band plan, and local practices, and ask your local club if anything is unclear.
There are no reviews to display.