Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

  • Entries

    2
  • Comments

    0
  • Views

    92

Entries in this blog

A good portable station isn't the one with the most gear. It's the one you can carry in one trip, set up in about 15 minutes, and use for a couple of hours without something failing. Whether you're activating a park for POTA, a summit for SOTA, a WWFF reference, or just practicing for Field Day, the same few decisions decide how the day goes: the antenna, the power, the logging plan, and the weather.

Start with the activation goal

Each program has its own thresholds, and they change, so check the current rules before you head out. As a general guide, POTA asks for a minimum number of contacts (ten) within a single UTC day for a valid activation. SOTA awards activator points for a small number of contacts (four), and WWFF uses a higher threshold (44). Knowing the target helps you plan time, band choice, and battery capacity. It also tells you whether you can afford to spend an hour on a fussy antenna.

Antennas: keep it simple and repeatable

Two designs dominate portable operating because they are light, cheap, and forgiving.

End-fed half-wave (EFHW)

  • What it is: a wire cut to a half wavelength on the lowest band, fed at the end through a matching transformer (commonly 49:1 or 64:1) that converts the very high end impedance to something your radio can accept.
  • Why people like it: a 40 m EFHW is also resonant on 20, 15, and 10 m. No band switching, no coax run to the far end, and a light feedline.
  • Watch for: common-mode current on the coax. A choke near the transformer or radio often makes a noticeable difference to both noise and SWR. Trim the wire in small steps and write the final length down.
  • Deployment: run it as an inverted L or sloper from a pole or tree branch. Keep the feed end off the ground if you can, and keep the wire away from metal fences, vehicles, and your body.

Linked dipole on a pole

  • What it is: a center-fed dipole with sections joined by small links. Connect the links for lower bands, disconnect them for higher ones.
  • Why people like it: it is a true dipole with a predictable feed point and usually a low SWR on each band it was built for. It needs no tuner.
  • Watch for: more connectors mean more things to mislabel or lose. Mark each band section clearly, and bring a spare link or two.
  • Deployment: a fiberglass or telescoping pole (roughly 6 to 10 m) holds the center up, forming an inverted V. The wire ends can be tied off low with cord and stakes.

Either way, pack a small bag of the things that fix most antenna problems: cord, a few tent stakes, a throw line and weight, spare connectors, and a short jumper of coax. If your antenna is resonant where you expect it to be, you have already solved most of the common field problems.

Power: calculate, don't guess

QRP, typically 5 W for CW and digital modes or up to 10 W on SSB, makes power planning easy. A rough way to size a battery:

  1. Find your radio's current draw on receive and at your transmit power. Check the manual or measure with an inline meter.
  2. Estimate a duty cycle. CW and SSB activations are mostly receive and short transmissions, but running POTA calls or digital modes raises the average.
  3. Multiply the average amps by the hours you plan to operate, then add a healthy margin (50 percent is reasonable).

Battery capacity is often given in amp-hours at a nominal voltage. A 12.8 V, 6 Ah LiFePO4 pack holds roughly 77 Wh. For a radio averaging around one amp, that is several hours of operating, but cold weather and heavy use cut that down.

Why LiFePO4 is popular

  • It gives a flat voltage curve, so your radio sees stable power until the battery is nearly empty.
  • It is lighter than a sealed lead-acid battery of similar capacity and tolerates many charge cycles.
  • A fully charged 4-cell pack sits around 13.3 to 14.6 V depending on how recently it was charged. Confirm that your radio's maximum input voltage covers that range.

Include an inline fuse close to the battery, use properly rated connectors, and check polarity every time. Charge LiFePO4 only with a charger designed for that chemistry, and avoid charging at freezing temperatures unless the pack explicitly supports it.

Solar is a supplement

A small foldable panel can extend a long day or top up a pack between trips, but cloud, angle, and shade reduce output a lot. Use a charge controller appropriate for your battery and don't count on the panel to run the radio on its own. Treat it as a bonus and size your battery to complete the activation without it.

Operating tips for activators and hunters

Activators should find a clear frequency, call CQ with the program name, and self-spot if the program's network allows it. Spotting is often what turns a quiet frequency into a pileup, so make sure the frequency and mode you post are accurate. Keep exchanges short and precise, and log as you go. If the paper log and digital log disagree, you will thank yourself later for writing the time and callsign down immediately.

Hunters can help by listening first, sending a callsign once or twice at a steady pace, and not calling over the person who is mid-exchange. Weak QRP signals reward patience. If the activator says to listen for a specific station or region, follow that. Park-to-park contacts are a fun extra for those running portable too.

Weather and safety come first

  • Lightning: if you hear thunder, take down the antenna and move to a safe shelter. A common rule is to wait around 30 minutes after the last thunder before resuming. Never use a tall pole or wire antenna during a thunderstorm, and especially not on a summit.
  • Power lines: set up far from overhead lines, with more clearance than the full height of the pole plus a margin for it to fall in the wrong direction.
  • Heat and cold: bring more water than you expect to use, sun protection, and a warm layer. Hands get cold fast when working a key or keyboard.
  • Wind: a tall pole is a sail. Guy it, or lower it if it starts to flex.
  • Tell someone your plan: where you're going, when you plan to be back, and what you'll do if plans change. Cell coverage in parks and on summits can be patchy.
  • Respect the site: follow park rules, stay out of restricted areas, don't stretch wire across trails where someone could trip, and pack out everything you brought.

A short pre-departure checklist

  • Radio, key or mic, headphones, and a spare power lead
  • Fused battery, charger, and a way to check voltage
  • Antenna, feedline, choke, pole, cord, and stakes
  • Logging gear (paper and pencil are fine) and a printout of the park or summit reference
  • Water, food, first-aid kit, sun and rain protection
  • A fully charged phone and a simple map or offline navigation

The best lesson: test at home

Most field failures can be found in a backyard trial. Set up the antenna, run the radio on the battery, make a few contacts, and time how long it takes. Fix whatever annoyed you, then repeat until the kit feels boring. A boring setup in the field means more time for the part you came for: making contacts, enjoying the outdoors, and maybe hearing a faint signal come back to your call.

When WSJT-X shows an empty decode window on a band that should be busy, or the radio won't key, the cause is nearly always one of a handful of things: the clock, the audio levels, or the rig-control link. This checklist works through them in the order that saves the most time.

Step 1: Confirm the basics before touching settings

  • Frequency and mode. Make sure the radio is on a standard FT8 frequency, such as 7.074 MHz on 40 m or 14.074 MHz on 20 m (USB, dial frequency), and that WSJT-X is set to FT8 rather than FT4 or another mode.
  • Band conditions. A quiet waterfall may just mean the band is closed. Try a band you know is open at that time of day before assuming something is broken.
  • Radio mode. Use USB-Data (or the equivalent) so the radio passes a flat audio response and doesn't apply voice processing.

Step 2: Fix your clock first

FT8 works in fixed 15-second slots, and the decoder only tolerates a small timing error between your computer and the station you're hearing. If the waterfall shows signals but nothing decodes, or you only decode some stations, suspect time. Many operators try to keep the clock within a fraction of a second.

  • Check that automatic time sync is enabled in your operating system. Default Windows sync intervals can be long, so many operators install a dedicated time-sync utility that polls more often.
  • On Linux and Raspberry Pi systems, a running NTP or chrony service normally handles this. On a Pi without a real-time clock, remember it relies on the network to get the time right after boot.
  • WSJT-X displays the time offset (DT) of each decoded signal. If most stations show a consistent DT of the same sign and size, the error is probably on your side.

Step 3: Set receive audio levels

In WSJT-X, the level meter at the bottom left shows your incoming audio. The user guide suggests aiming for roughly 30 dB on the meter, and you should avoid anything in the red, which means clipping. Too little audio won't hurt decoding as much as too much will, because overdriven input distorts and spreads signals across the passband.

  • Adjust the radio's USB audio output level or the operating system's input slider, not both at once.
  • Turn off any audio enhancements, AGC-style processing, noise suppression or microphone boost on the sound device in your operating system.
  • Set the sample rate to 48,000 Hz, 16-bit, if your system offers a choice.
  • In Settings > Audio, check that the input device is the radio's codec and not a webcam, headset or built-in microphone. USB devices often appear with generic names such as "USB Audio CODEC", and the order can change after a reboot or when you plug into a different port.

Step 4: Get CAT control working

In Settings > Radio, WSJT-X uses the Hamlib library to talk to most transceivers. Choose your rig model, serial port, baud rate, data bits, stop bits and handshake to match the radio's menu settings, then press Test CAT. The button turns green when the link works and red when it doesn't.

If it stays red, check in this order:

  1. Baud rate mismatch. The radio's CAT or CI-V speed must match what WSJT-X is set to. Some radios also have an auto setting that can cause trouble.
  2. Wrong COM port. USB-serial adapters can be renumbered by Windows. Check Device Manager or, on Linux, the device list under /dev/serial/by-id, which is more stable than ttyUSB0 style names.
  3. Port in use. Only one program can open a serial port at a time. If a logger, rig-control program or another digital program already holds it, WSJT-X can't connect.
  4. Driver problems. Many radios use common USB-serial chips. A missing or outdated driver often shows up as a port that vanishes or can't open.
  5. Radio-side settings. Some radios need CAT enabled, a particular USB or serial function selected, or a CI-V address set to match.

Step 5: Sort out PTT and split

PTT can be keyed by CAT command, RTS or DTR serial lines, or VOX. CAT is usually the simplest on modern radios with built-in USB. Use Test PTT to confirm the radio actually keys before you try a real transmission, ideally into a dummy load.

The Split Operation setting matters more than people expect. WSJT-X is designed to keep your audio tone in a sweet spot (roughly 1500 Hz) while the dial moves. Choosing Rig uses the radio's true split mode, while Fake It retunes the dial around transmissions. If the transmitted signal looks distorted or your radio keeps retuning, try the other option.

Step 6: Don't overdrive the transmitter

FT8 is a constant-envelope mode, but your audio chain still has to be linear. The usual approach:

  • Set the radio to a modest power level.
  • Use WSJT-X's Pwr slider and your computer's output volume to bring up drive until you see just a hint of ALC movement, then back it off so ALC reads zero or near it.
  • Remember that more audio does not mean more power in a clean signal. It means splatter that annoys neighbors on the band.
  • Mute system sounds, notifications and other applications so nothing unintended goes out over the air.

Step 7: Check whether anyone hears you

Once you're transmitting, PSK Reporter is a handy independent check. Enable spotting under Settings > Reporting, then look up your callsign on the PSK Reporter website to see which stations reported you and where. Your grid square needs to be correct in WSJT-X for the map to make sense. Spots appearing within a few minutes tell you the whole chain is working; no spots on a band that other stations clearly use points to an antenna, power or audio issue.

For CW and RTTY, the Reverse Beacon Network does a similar job for those modes, though it won't see FT8.

Step 8: Share the radio with logging software

A common trouble spot is running WSJT-X alongside N1MM+ or Log4OM. Both of those programs normally want to control the radio too. Options include:

  • Let WSJT-X own the serial port and have your logger read frequency and mode from it via UDP rather than direct CAT.
  • Use a rig-control middleman, such as a program that shares the radio between several applications through virtual serial ports.
  • Use the radio's second virtual port if it provides one.

For logging, WSJT-X can broadcast its decodes and logged QSOs over UDP, which loggers and helper tools can read. Check that the UDP server address and port match on both ends, and that no firewall is blocking them.

A quick diagnostic table

  • Waterfall looks fine, no decodes: clock, wrong mode, or audio level too high.
  • Waterfall is blank: wrong input device, muted input, or radio not in USB-Data.
  • Test CAT is red: baud rate, COM port, driver or another program using the port.
  • Radio keys but no output: output device set to the wrong sound card, or audio muted.
  • Transmits but no spots: band closed, wrong grid, or no reporting enabled.

Final thoughts

Change one thing at a time and re-test after each change. Writing down the settings that work once you have a stable setup saves a lot of grief after an operating system update or a new USB port shuffles your devices. If you run a Raspberry Pi or a dedicated shack PC, consider documenting the device names and baud rates somewhere you can find them in a hurry.


Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.