Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 116
SN 115
A 4
K 1 Quiet
X-Ray B8.0
Wind 426.6 km/s
Aurora 1
Updated 01:30 UTC HamQSL · N0NBH
Day 80/40m Fair 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

How close to the band edge is too close? Allocations vs. band plans, and where to park

ci_cover.jpg

I'm fairly new to HF and still sorting out what counts as a rule and what counts as a convention. My license lists frequency ranges for each band, and the club's printed band chart shows extra segments inside those ranges for CW, digital, phone and so on. Two things confuse me.

First, are the segments on the band chart legally binding, or only the outer limits in the regulations? Second, how do I think about operating near the edge of a band? If my privileges run to a certain frequency, can I put my dial right at that number, or do I need to leave room? I'd like to understand the logic rather than memorize numbers for each band.

I'm also unsure how to choose a spot on a band when I have several legal options.

  • Replies 2
  • Views 30
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

It helps to separate three layers: allocation, privileges, and band plan.

An allocation is the service-level assignment of spectrum. It starts with the ITU Radio Regulations and is then implemented nationally. Your privileges are what your own license class lets you do within those allocations, sometimes limited by mode or power. Both are legal matters, and the national regulator's current rules are the authority. A band plan is usually a voluntary agreement among operators, such as the IARU regional plans or national society plans. It isn't law in most places, but it keeps incompatible activities from running over each other. Some countries do write parts of it into the license conditions, so check yours rather than assuming.

The band plan still matters in practice. A wideband digital signal in the middle of a weak-signal CW segment is probably legal, but it will wreck other people's contacts and you'll hear about it.

For band edges, the number on your dial is not where your signal ends. The whole occupied bandwidth has to fit inside your privileges. On the top edge of 20 meters, which is 14.350 MHz in the ITU allocation, a USB voice signal about 2.8 kHz wide with the dial at 14.348 would extend to roughly 14.3508. That is out of band. On USB the signal sits above the displayed carrier frequency, and on LSB it sits below. So use USB margin at the upper edge and LSB margin at the lower edge. This is also why conventions put LSB on lower bands and USB on higher ones, though that is a convention and not a rule.

Keep a margin beyond the arithmetic, too. Rig calibration isn't perfect, and a few hundred hertz of cushion is cheap insurance. Check the rig against a known accurate reference now and then.

Adding to the edge discussion, because modes other than SSB each have their own quirks.

With CW, the frequency shown on the dial may or may not be your actual transmit frequency, depending on how the rig handles sidetone and pitch offset. Hard keying with fast rise and fall times also creates key clicks that spread well beyond the nominal tone. A narrow CW signal can still splatter outside the band if you're sloppy and sitting right on the line.

With digital modes like FT8, the usual practice is to set the dial to a standard frequency in USB. The audio tone offset you see on the waterfall is added to that dial frequency, so the actual RF signal is the dial frequency plus the tone. Near an upper band edge, add the offset and the signal bandwidth together. The same applies when you pick a tone high in the passband to dodge a neighbor.

As for choosing a spot, a few habits help:

Look at the band plan for your region first. IARU Regions 1, 2 and 3 differ, and some bands have different widths. For example, 40 meters has historically been 7.000 to 7.200 MHz in Regions 1 and 3 but 7.000 to 7.300 MHz in Region 2. Check your regulator for what applies to you.

Listen for a while before transmitting. Ask on frequency if it's in use, and be ready to hear no answer even when someone is there.

Stay off beacon and special-purpose frequencies. The NCDXF/IARU beacon network is on 14.100, 18.110, 21.150, 24.930 and 28.200 MHz, and you shouldn't set up camp right on them.

Don't park on calling frequencies or the standard digital watering holes. Make contact there if that's the convention, then move off.

Finally, if a band has a secondary allocation, such as 30 meters in many places, you must not interfere with the primary users. That band is also usually limited to narrower modes and lower power, so look at the details in your own rules.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.