Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a field comms station: antenna choice, power budget, and keeping generator noise out of the receiver

ci_cover.jpg

I'm putting together a plan for a portable HF/VHF station that has to run for a full day or more away from mains power. This is a planning exercise, not a report on a finished build, and I'd like input on where the weak points usually are. The target is a 100 W HF rig for SSB and digital modes, a dual-band VHF/UHF mobile for local coordination, and a laptop for logging and FT8/packet-style modes.

Antenna thinking so far: an end-fed half-wave (EFHW) on a telescoping mast or tree-supported line for 40/20/15/10 m, with a 1:1 choke at the feedpoint of the coax and another at the radio end. As a backup, a simple 40 m dipole with a center insulator and a choke, since it is easy to troubleshoot. For regional contacts on 80/40 m, I'm considering keeping the dipole low enough to give a high takeoff angle (NVIS-style) rather than putting it as high as possible. For VHF, a roll-up J-pole or a small Yagi on a push-up mast.

Power thinking so far: a 12 V LiFePO4 battery as the main source, with an inverter generator held in reserve for recharging rather than running the station directly. My rough budget is receive current of 1.5 to 3 A including the laptop, and transmit peaks of 20 to 22 A at 100 W on SSB, with a much lower average because of speech duty cycle. FT8 and other digital modes are different: they are close to continuous carrier for 12 to 15 seconds at a time, so I plan to turn power down to 30-50 W instead of running full output.

The questions I'd like answered: (1) What is the best way to estimate real amp-hours for a day of operating instead of just trusting the battery label? (2) How far from the operating position should a generator sit before its noise stops showing up on the receiver, and does it help to run from battery with the generator off while actually operating? (3) Is the EFHW worth the convenience, or does it cause more common-mode and tuning trouble than a dipole in practice?

  • Replies 2
  • Views 52
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

For the amp-hour estimate, build a table by mode instead of using one average. Split the day into receive time, SSB transmit time, and digital transmit time, then multiply each by its current draw. For SSB, a 100 W rig may peak above 20 A, but with speech and normal transmit/receive cycling the average transmit draw is well below that. For FT8, treat transmit as close to continuous current for the whole transmit window, and remember the receive half of each cycle still draws current. Then add accessories: laptop, tuner, USB hubs, lights, and anything running from a DC-DC converter. Those small loads add up over many hours.

Then apply a safety margin. Rated capacity is nominal, cables and fuse holders lose some voltage under load, and cold weather reduces usable capacity. LiFePO4 holds voltage well, but check that your rig's low-voltage cutoff and the battery's BMS cutoff don't conflict. Some rigs misbehave or distort before the battery is actually empty, particularly if the supply lead is long or thin. Use short, adequately thick DC leads, fuse near the battery, and measure voltage at the radio during transmit, not at the battery terminals.

On the generator, noise comes from two places: radiated hash from the generator and its inverter electronics, and conducted noise on any cable that connects the two systems. Distance helps with the first, and common-mode chokes and keeping the systems separate help with the second. Run the generator as far away as the cable and safety situation allows, and position it downwind and in the open because of carbon monoxide. Never run it in a tent, vehicle, or enclosed space. If you charge the battery with a mains charger while operating, expect that charger to be a noise source too. Charging between sessions and operating from battery alone is the quietest approach, particularly on 80 and 40 m where the receiver is sensitive to broadband noise.

  • Moderators

The EFHW is a reasonable choice for a compact multiband antenna, but it depends heavily on how the feedline and counterpoise behave. The matching transformer at the feedpoint presents a high impedance that is only roughly 50 ohms after transformation, so the SWR on each band can vary with wire height, sloping geometry, and nearby objects. The coax shield also tends to become part of the antenna, which is why you plan chokes. I would put the first choke close to the transformer and a second one at the radio end or a short distance back. Test both on receive, since a noisy receiver often improves when the choke is added.

A dipole is easier to reason about because it is balanced and resonant on a single band with predictable feedpoint impedance. If operations are mostly 40 m and one higher band, a fan dipole or a simple dipole for each band can be more predictable than an EFHW that may need a tuner. The tradeoff is more support points and wire. For NVIS on 80/40 m, a dipole 0.1 to 0.25 wavelength above the ground is a typical starting range, and it tends to favor close-in contacts over long distance. Pick the height based on the distances you need to cover, not on what feels tidy.

Before leaving, set up everything once as a dry run: antenna, feedline, battery, radio, laptop, and any DC converters. Check the receiver noise floor with the generator off, then with the generator running at several distances, and record what changes. Also check SWR across the bands you plan to use and confirm that the radio doesn't reset or show RF feedback on the laptop interface during transmit. USB cables and audio interfaces are common weak spots, and snap-on ferrites on the USB, power, and audio leads are inexpensive to try. Finding those faults in the yard is much easier than in the field.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.