Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a first 40 m dipole from scratch: wire, supports, choke, trimming, and how far to trust the model

ci_cover.jpg

Here is a plan for a basic homebrew 40 m inverted-V, and I'd like feedback on the weak points before any wire gets cut. The idea is a center-fed half-wave dipole with its apex on a telescoping fiberglass pole, the ends sloping down to tie-offs, fed with 50 Ω coax through a current choke at the feedpoint. It's the kind of build that teaches most of the fundamentals: resonance, feedpoint impedance, common-mode current, and the gap between a model and a real backyard.

Starting length. The usual rule of thumb is 468 / f(MHz) feet for the full dipole. At 7.1 MHz that's about 65.9 ft, or roughly 33 ft per leg. Real antennas rarely land on the formula. Height, nearby objects, wire insulation, and the sloping legs of an inverted-V all pull the resonant frequency. The sensible approach is to cut each leg a few percent long, fold the excess back at the end insulators without cutting, and trim in small steps.

Wire. For a permanent span, 14 AWG hard-drawn copper or copper-clad steel resists stretch better than soft-drawn copper. Stranded insulated wire is easier to handle and coil for portable use, but the insulation lowers the resonant frequency slightly, so the wire usually ends up a bit shorter than the bare-wire figure. Thinner wire (16–18 AWG) is fine for light portable use at QRP and low power, but it has less mechanical margin.

Feedpoint and supports. The center insulator has to carry the weight of the coax and the pull of the legs, so strain relief matters more than the electrical connection. A common approach is to tie the wire through the insulator holes and then solder the jumpers to the connector terminals, so the solder joint carries no tension. At the ends, use any UV-resistant insulator with a rope that won't rot or stretch badly, and allow some slack or a tensioning method so wind and tree movement don't snap the wire.

Questions for the thread:

  • What apex angle is a reasonable compromise for an inverted-V on a pole around 10 m high? I've seen 90–120° suggested to keep the feedpoint near 50 Ω.
  • Is a ferrite-bead choke or a coiled-coax choke the better choice at 40 m for a first build?
  • Should I model this in EZNEC or MMANA-GAL before building, or just build and trim?
  • Replies 2
  • Views 53
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the choke: both types work, but they behave differently. A coiled-coax choke (several turns of the feedline itself, close to the feedpoint) is cheap and easy, but its impedance peaks around a fairly narrow range set by the coil's inductance and stray capacitance. It's worth checking that the peak actually falls near 7 MHz and not somewhere else. A ferrite choke wound with coax through a stack of cores, usually a mix such as 31 for lower HF, has a broader response. Aim for a choking impedance of at least a few kilohms, mostly resistive. What you want is to suppress common-mode current on the outside of the coax shield, so the feedline doesn't become part of the antenna and the pattern and SWR readings don't depend on how the cable is draped.

That ties directly to measuring. If you measure SWR at the radio end through a long, lossy coax, the loss flatters the reading. An analyzer connected at the feedpoint (or at the end of a short line) gives the truer picture of the antenna. Also note that if the reading changes when you move the coax or touch it, you probably have common-mode current, and the choke isn't doing its job.

For trimming: find the frequency of minimum SWR (or zero reactance on an analyzer) and compare it to your target. If resonance is low, the wire is too long. As a rough guide, for a half-wave dipole, a 1% change in length moves the resonance by about 1%, so at 7 MHz, expect roughly 70 kHz per 1% of total wire. Shorten both legs equally, in small amounts, and re-measure each time. Don't trust a single sweep, and repeat it if the wire sways.

On apex angle, a flatter inverted-V (closer to 120°) tends to raise the feedpoint impedance toward the dipole's free-space value, while a steeper V lowers it. Either is usually within what a typical transceiver tolerates with a decent match. The tradeoff is more about where the ends can be anchored safely, since the end wire shouldn't hang within reach of people or pets.

  • Administrators

To answer the modeling question: do both, in that order. A model won't predict your exact trimming result, since your ground, trees, and nearby wiring aren't in it, but it's very good for relative questions: how much does the feedpoint impedance change with apex height, how does the inverted-V angle affect it, and what happens if you swap the coax feed for open-wire line on a different band? Both EZNEC and MMANA-GAL are useful. EZNEC uses NEC and has a well-known ground model with a good reputation for accuracy. MMANA-GAL is free, uses a different solver, and is popular for quick wire-antenna work. Free or demo versions of some programs limit segments, so check the current limits before planning a complex model.

A few modeling habits save a lot of confusion. Use enough segments per wire, and keep adjacent segments at similar lengths where wires meet at an angle. Enter the actual wire diameter. Pick a realistic ground type instead of leaving it at perfect ground. If the software offers an accuracy check, such as the average gain test in NEC-based tools, use it to catch bad geometry. And remember that the model assumes bare wire unless you add insulation effects, so insulated wire will usually need to be a few percent shorter than the model says.

If the dipole later grows into a multiband setup, ladder line is worth modeling too. A center-fed half-wave on 40 m fed with 450 Ω window line and an ATU is a flexible multiband arrangement because the feedline's loss stays low even with a high SWR on it. The line should run away from metal and not parallel to a mast or gutter, with a balun or choke at the tuner side to keep common-mode current under control. Trap dipoles save space but trade it for bandwidth and efficiency, and the traps add weight to the wire.

Verticals are a separate problem, mostly about the radial system. A quarter-wave vertical over a good ground has a feedpoint impedance near 36 Ω; with real ground losses it typically reads higher. A ground-mounted vertical usually wants a lot of radials, with returns diminishing past a certain count. An elevated vertical can work with fewer radials, often four or so, cut to a quarter-wave and sloped downward, which also raises the feedpoint impedance toward 50 Ω. The fiberglass pole can support either a wire vertical or the inverted-V apex, so one pole could serve for testing both.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.