Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a multiband wire antenna from scratch: wire, chokes, ladder line, and how far to trust modeling and SWR

ci_cover.jpg

This thread is for comparing notes on a from-scratch wire antenna build. The example is a center-fed doublet or fan dipole for 40 through 10 m, plus a possible 20 or 40 m vertical, but the questions apply to most homebrew HF antennas. The aim is to work out which decisions affect performance and which are mostly habit.

Start with length. The usual formula is 468 / f(MHz) feet for a half-wave dipole. That gives about 66 ft overall for 7.1 MHz and about 33 ft for 14.2 MHz. Treat the result as a starting point. Height above ground, nearby objects, wire insulation, and end insulators all shift resonance, and insulated wire usually resonates a few percent lower than bare wire. Cut long, then trim in small steps while watching resonance on an analyzer.

For wire, 14 AWG hard-drawn copper or copper-clad steel is a common choice for permanent spans. 12 AWG is stronger, and 18 to 20 AWG is fine for portable or short-term use. Plain soft-drawn copper stretches over time, which slowly changes the length and sag. Copper-clad steel resists stretch, and at HF the RF current stays in the copper layer, so it works well for long spans.

On the hardware side, a center insulator needs strain relief so the feedline's weight never hangs on the solder joints. Coax ends need sealing, because water wicks into the braid. Polyester or Dacron rope holds up to UV much better than cotton or cheap nylon. HDPE or ceramic insulators are fine at HF power levels.

Questions for the thread:

1) When feeding a doublet with ladder line and a tuner, do you add a 1:1 or 4:1 balun at the tuner, or rely on the tuner's built-in one? 2) Is a ferrite choke at the feedpoint worth it on a coax-fed dipole, and what mix and how many turns? 3) How much do you trust a model or an SWR reading before cutting wire? Share any build data you've measured, such as final lengths, heights, and analyzer R and X values.

  • Replies 2
  • Views 51
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On chokes, the goal is high common-mode impedance on the coax outside, not a perfect-looking SWR curve. A coax-fed dipole with no choke lets the shield carry current and act as part of the antenna. That distorts the pattern, can bring RF into the shack, and can make analyzer readings depend on how the coax is routed. A common approach is a stack of type 31 ferrite cores with the coax wound through them, which works well from the lower HF bands upward. Type 43 is often used toward the higher bands. A small coil of coax (an air choke) can also work, but it is naturally resonant and tends to be effective only on certain bands, so it is less broadband than ferrite. Also, ferrite can overheat if the choke is poorly matched or sees high common-mode voltage, so size the cores for your power level.

For ladder line with a tuner, the best arrangement is usually to keep the line balanced all the way to the tuner's balanced output or a good current balun there. Window line has low loss even at high SWR, but it needs clearance from metal gutters, downspouts, and other conductors. Make bends gentle and use a few twists only if the line is a type that tolerates them. A 4:1 balun is a transformer, not a magic fix. At high impedance mismatches it can heat and lose efficiency, so a 1:1 current balun is often the safer starting point for a doublet, with the tuner handling the match.

On traps: a parallel LC trap acts as a high-impedance isolator near its resonant frequency and as an inductor below it, which shortens the antenna's electrical length on the lower band. The tradeoffs are narrower bandwidth, some loss in the coil and capacitor, and the need for weatherproofing and capacitors with sufficient voltage rating. A fan dipole avoids traps, but the elements interact, so expect to prune each one in turn.

  • Administrators

On modeling and measuring, the two tools tell you different things. EZNEC uses the NEC engine, which handles real ground and wires at different heights well. MMANA-GAL is MININEC-based and is quick to set up, and many builders find it convenient for small antennas. Either way, the same basics apply. Use enough segments (a common rule is at least ten per half-wavelength, more near junctions and bends), put the source on a segment that makes sense geometrically, and choose the ground type deliberately instead of leaving free space on. Compare height variations such as 30 ft versus 45 ft and see how the feedpoint resistance and takeoff angle change. A model that leaves out the coax shield won't predict common-mode problems, so if that matters, model a short length of feedline as a wire. Check any limits in the version you have, since free or demo editions may restrict the number of segments.

For SWR, an antenna analyzer at the feedpoint gives the most honest picture. Measured at the shack end, coax loss makes the SWR look better than it is. Resonance is where reactance crosses zero (X = 0), and that is not always where SWR is lowest unless the resistance is near 50 ohms. Read R and X together. Calibrate against a known 50 ohm load before you start, keep the analyzer's output low, and watch for strong broadcast stations that corrupt readings. Move the coax and see if the numbers change, which is a quick test for common-mode current.

For the vertical, a quarter-wave is about 234 / f(MHz) feet, so roughly 16.5 ft on 20 m and 33 ft on 40 m. A fiberglass pole supporting a wire element works well, but check that the pole has no carbon fiber in it, since carbon is conductive and can detune the antenna. Radial count matters more than most things on a ground-mounted vertical. Many radials, commonly 16 or more, lower ground loss, while elevated systems can do well with a few resonant radials sloping downward. Sloping them also pushes the feedpoint impedance closer to 50 ohms than horizontal radials do.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.