Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a two-rig HF shack with a future amp: power, bonding, filtering and RFI control

ci_cover.jpg

I'm sketching a shack layout and want to sanity-check the order of operations before buying anything else. The plan is a main 100 W class transceiver (something in the IC-7610 / TS-890S / FTDX10 category) and a smaller second rig for portable use and as a backup (KX3 or G90 class). Both would share a desk and ideally a single power system. A solid-state amplifier in the 500 W to 1 kW range is likely within a year or two, so I'd like to avoid rewiring everything when it arrives.

These are the points I'm unsure about.

Power: one large supply for both rigs and the amp's control circuits, or separate supplies? Most 100 W rigs specify around 20 to 23 A peak at 13.8 V, but the exact figure is in each manual. How much headroom is sensible, and does a switching supply cause trouble on 160 m through 20 m, or is that mostly a question of which model you pick?

Grounding and bonding: I understand the rod outside is not an RF ground, and that the AC safety ground and the station ground need to be bonded to the same system. What I'm less sure about is what to do inside the room. Do I run a bonding strap or bus behind the desk and tie every chassis to it, or does that create loops that cause more RFI than it cures?

Filtering: when are band-pass filters worth it? If I only ever run one rig at a time, do they matter, or are they only for two transmitters operating at once?

Tuner placement: an internal ATU plus an external tuner at the operating position, or should the tuner live at the antenna feedpoint for anything with a high-SWR feedline?

Any layout or order-of-purchase advice is welcome, especially for the amp interface (ALC, keying, band data) before it arrives.

  • Replies 2
  • Views 50
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Start with safety bonding, because everything else builds on it. The AC equipment grounds keep the chassis safe on a fault, and the station ground is there for lightning and static. If you add a separate ground rod for the antenna entry, it must be bonded to the service entrance grounding system. Two unconnected ground systems can put a dangerous potential between them during a strike. Check your local electrical code, or have an electrician verify it, rather than relying on forum rules of thumb.

For RF inside the room, short and wide beats long and thin. A copper strap or a short bus bar that every chassis ties to is fine, but its job is mainly to keep the equipment at the same potential. It will not fix common-mode current coming down the coax. That is better handled with chokes: a ferrite choke (a type 31 mix is commonly used for HF) at the feedpoint and another where the coax enters the shack. Chokes there often fix more problems than extra ground wire.

The loop worry is real but usually shows up as audio hum or USB noise, not RF. Keep AC cords and DC leads away from coax and audio cables, and cross them at right angles where you have to. If a USB audio connection hums, try an isolator or a powered hub on the same strip before blaming the ground system.

On power, headroom matters more than the label. A supply rated for about 30 A for a 20 to 23 A rig stays cooler and quieter and rides out voltage sag on transmit. Whichever way you go, use heavy-gauge DC leads, keep them short, and fuse each positive lead near the source. Powerpole distribution makes adding the second rig or the amp's control supply much easier later.

  • Moderators

On band-pass filters, the usual answer is that they are for multi-transmitter setups. With one rig transmitting at a time you don't need them for the main receiver, since modern 100 W rigs already have band filtering in front of the front end. The IC-7610, for example, has a preselector. Filters matter when one transmitter on 20 m can overload a receiver that is listening on 15 m in the same room, as in SO2R or a multi-op station. If the second rig is mainly a backup or portable unit, you can skip them for now. If you start running two rigs side by side, add them then, and put them in line with the receive path as well as the transmit path.

On the tuner, an internal ATU only matches within a limited range, often around 3:1 on many rigs. It makes the transmitter see a good match, but it does nothing about loss in the feedline. If you're feeding a non-resonant antenna with ladder line or a long coax run at high SWR, the tuner at the feedpoint (or a remote ATU) wastes much less power than a tuner at the radio. For an antenna that is already near 50 ohms on most bands, the internal ATU is enough, and an external tuner is mostly worth it when you add the amp.

For the amp, plan the interface now. Most solid-state amps want a keying line, and many can take band data from the radio so they follow band changes automatically. Check which cable each of your radios supports before buying, because the connectors differ between brands. Set the exciter drive so the amp reaches full output with little or no ALC action, and tune the ATU at low power before bringing the amp online. With the amp running, keep an eye on RF in the room: poor common-mode choking shows up as a hot mic, a rig's display glitching, or SWR readings that change when you touch cables.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.