Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bring-up order for a homebrew QRP transmitter: what to verify before it sees an antenna

ci_cover.jpg

A lot of homebrew transmitter problems, whether it's a Tuna Tin 2 style crystal oscillator and PA, a Pixie, a BITX board or a modified uBITX, come from skipping steps between "it powers up" and "it's on the air." Here is a bring-up order that works for most low-power builds. I'd like to hear where others would change it.

1. Power first, with protection. Use a bench supply with the current limit set low, or a series resistor or fuse if you don't have one. Put a reverse-polarity diode or a series Schottky in the supply line, or a fuse plus a diode across the input. Before any RF testing, measure the DC rails and look at idle current. A transmitter stage drawing far more than the schematic suggests with the key up is usually self-oscillating or biased wrong.

2. Check the oscillator on its own. Confirm it starts reliably, sits on the intended frequency, and has a clean note in a separate receiver. With crystal oscillators, listen for chirp when keyed. With VFO or Si5351-based rigs, check that the frequency stays put after a few minutes of warm-up and that nearby stages don't pull it.

3. Terminate the output in a dummy load, never an antenna. A 50 ohm non-inductive load is ideal. For a few hundred milliwatts, several carbon-film or metal-film resistors in parallel work, but check their power rating. Measure RF across the load with an oscilloscope and a properly compensated probe, and use P = (Vpp / 2.828)² / 50. In practice that is Vpp² / 400. So 10 Vpp across 50 ohms is about 0.25 W, and 20 Vpp is about 1 W. Scope readings get unreliable as frequency rises, and a probe adds capacitance, so treat the result as a good estimate rather than lab-grade.

4. Look at harmonics before you call it finished. This matters most for simple Class C or hard-driven stages. A single transistor PA can put out strong harmonics, and a Pixie-style transmitter has very little filtering unless you add it. A low-pass filter sized for the band, with inductors wound to the right turn count on the right core material, is not optional. A spectrum analyzer is best. Without one, a second receiver tuned to the second and third harmonics, with a dummy load attached, will at least show whether they are strong. A well-calibrated SDR with attenuation in front can also help, but never connect transmitter output directly to a receiver input.

5. Validate your SWR bridge before trusting it. Check it with known terminations. A good 50 ohm load should give a very low reflected reading. Two 100 ohm resistors in parallel make 50 ohms. A single 100 ohm resistor should read about 2:1, and so should 25 ohms (two 50 ohm loads in parallel). An open and a short should read as nearly total reflection. If the bridge fails these, the antenna measurements that follow won't tell you much.

6. Keying and power-supply noise. Look at the keying envelope. Sharp edges make key clicks that splatter well beyond the signal. A simple RC shaping network on the keyed line often helps. Also check whether the supply, especially a cheap switching one, adds noise to a direct conversion receiver. Hum or whine on the audio may be coming from the supply, not the receiver.

Only after these steps would I connect an antenna, and then at low power, with a tuner or matching network if needed. What do you all do first when a build isn't behaving, and which of these checks do you skip when you shouldn't?

  • Replies 2
  • Views 51
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The harmonic check deserves more emphasis. A lot of people stop at "I measured 1 W into a dummy load, so it works," but that tells you only how much total RF there is, not where it is. A scope reading includes every harmonic, so a rig that looks like 1 W on 40 m might put out less than that in the fundamental.

If you have to use a scope, put a 50 ohm termination at the load and use the shortest ground lead you can on the probe, because the long ground clip on a typical probe adds enough inductance to distort readings at HF. A small test-point pickup, or a probe tip with a ground spring, will get you closer to reality.

One more caution for bench work: a toroid filter built with the wrong material or a miscounted turn count won't show a problem until you actually check the output. Counting turns by passing the wire through the core's center hole (each pass is one turn) is easy to get wrong. An LC meter or a nanoVNA is cheap insurance for verifying a filter before it goes into a rig.

  • Administrators

I'd add one pre-step: inspect and clean before you apply power. A lot of kit failures are solder bridges, cold joints, a transistor in backwards, or a part with the wrong value. Reading resistor color codes again with a meter takes ten minutes and can save a damaged transistor. Electrolytic capacitor polarity and diode orientation are the two I'd check twice.

For direct conversion receivers specifically, I'd treat the audio chain as its own bring-up stage. Touch the audio input and listen for hum, then connect the mixer and see if you get a rushing noise that rises with signal. If you hear broadcast AM breaking through, that is a common weakness of direct conversion designs without front-end filtering, so a bandpass filter ahead of the mixer is worth adding.

On the kit-versus-scratch question: with a BITX or uBITX-type board, it's tempting to modify things early. Getting it working as designed first gives you a baseline to compare against when you do start changing parts. Otherwise you can't tell whether a new problem came from your modification or was already there.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.