Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a VHF/UHF antenna setup: how do you weigh gain, pattern, feedline and connectors?

ci_cover.jpg

A lot of VHF/UHF antenna advice sticks to one number, gain, and ignores everything between the radio and the sky. I'd like to compare notes on the whole chain: antenna type, pattern, polarization, coax, connectors and mounting. Each choice affects the others.

Gain and pattern. A vertical omni's gain comes from squashing the donut-shaped pattern, not from making more power. A quarter-wave whip on a good ground plane is roughly 0 dBd. A 5/8-wave is commonly quoted at about 3 dB over a quarter-wave, with a lower takeoff angle. Collinears stack more radiating sections and flatten the pattern further. That helps on open, flat terrain or with a fixed station talking to distant stations. It can hurt when the other station is far above or below you, or when a vehicle is tilting and bouncing. Also remember that dBi is 2.15 dB bigger than dBd for the same antenna, so compare like with like.

Simple wire and tube designs. The J-pole is a half-wave radiator end-fed through a quarter-wave matching stub. The slim jim is the same idea, folded. Both are cheap and need no radials, which makes them attractive. But with no ground plane, the outside of the coax shield can become part of the antenna. A choke near the feedpoint, such as ferrite or a few turns of coax, often cleans up pattern distortion and RF in the shack. Don't expect more than about dipole-level gain from either one, whatever the sales photos suggest.

Mobile. A quarter-wave whip is the baseline: about 19 inches on 2 m and about 6.5 inches on 70 cm, before trimming. It needs a ground plane, so the roof does most of the work. A mag mount is quick and removable, but its coax is usually thin and runs through a door or hatch seal. An NMO mount (a 3/4-inch hole, a threaded base, and a whip that screws on) is more permanent and mechanically better. In both cases, the whip's SWR depends on the metal under it. Moving the mount off the roof center can shift the match and change the pattern.

Coax and connectors. At VHF, thin RG-58-type cable loses several dB per 100 ft, and the loss roughly doubles at 70 cm. RG-213 or a low-loss cable like LMR-400 is much better on any run longer than a short jumper. Check the manufacturer's loss chart for your frequency, because 'same size' cables vary a lot. For connectors, PL-259/SO-239 (UHF connectors) work on 2 m but aren't constant-impedance, aren't truly weatherproof, and aren't a great choice at 70 cm. N-type is constant 50 ohm, handles weather better when sealed, and suits outdoor UHF joints. Whichever you use, a poorly crimped or soldered connector is a bigger problem than the type.

SWR. SWR tells you how well the load matches the line, not how well the antenna radiates. A dummy load gives a great SWR and radiates nothing. Long lossy coax also hides a bad antenna match, because reflected power is attenuated on its way back. Measure close to the antenna when you can, and keep the meter between the radio and a known-good feedline.

Polarization and use case. FM repeaters and most local simplex use vertical polarization, so a yagi pointed at a repeater should usually be mounted with its elements vertical. Weak-signal SSB/CW work usually uses horizontal. Mismatched linear polarization can cost you many dB. Satellites add a complication. Handheld Arrow-style yagis are linear and can fade as the satellite's orientation changes, while crossed yagis or other circularly polarized arrays reduce that fading but need more installation effort. Repeater sites bring duplexers, isolation and vertical spacing into it, which is a separate topic.

So here's my question. If you're building one antenna system for local FM repeaters, simplex, and an occasional satellite pass, where do you spend the money first: the antenna, the coax, or the mounting hardware? And what would you skip altogether?

  • Replies 2
  • Views 46
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd spend on the feedline and mounting before the antenna, if the run is more than a few meters. A 6 dB antenna on lossy coax at 70 cm can easily end up behind a plain quarter-wave on a short run. Do the loss arithmetic with real figures from the cable datasheet for your band, then add roughly 0.1 to 0.3 dB per connector pair as a rule of thumb.

For a fixed station, I'd lean toward a collinear or a 5/8-wave vertical for local FM, if the terrain is fairly flat or you are working a repeater at a similar elevation. If the nearby repeater is on a hill above you, extra gain flattening the pattern can disappoint, and a simpler lower-gain antenna may work as well. A yagi is the better tool if there's one specific repeater that's marginal. It cuts noise and adds gain, but it needs a rotator or a fixed heading.

On connectors, a short N-to-PL-259 pigtail is a sensible way to use a mixed set of radios without putting a UHF connector out in the weather. Whatever the connector, tape or seal it properly and make a drip loop. Water in the coax is a classic cause of an SWR that creeps up over months.

  • Moderators

On the polarization point: don't skip the choke, particularly with J-poles and slim jims. If the pattern looks distorted or you pick up RF in the shack, the outside of the coax is a good suspect. A choke close to the feedpoint, and sometimes another a half-wave or so down the line, is a cheap test. It's easy to repeat with and without it, using the same location and a signal you can measure. Don't rely on SWR alone for that comparison, because it won't tell you what happened to the pattern.

For satellite work with FM birds, the hardware is often simpler than people expect. A small handheld yagi plus a dual-band radio can work for a start, with a lot of the effort going into Doppler tuning and aiming. A fixed omni can catch high passes, but weak low-elevation passes are where a directional antenna shows its benefit. If you go for circular polarization, check the handedness spec and the phasing line details in the antenna's documentation, because a mismatch there costs you signal.

For mobile, I'd choose NMO over a mag mount if you intend to leave the antenna on. A good, well-grounded mount at the roof center gives the most predictable results. If you're using a magnet mount, check the SWR with the antenna in its actual position and keep the coax from being pinched. Trim the whip length per the manufacturer's instructions, shortening in small steps, because you can't put metal back.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.