Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM field station: how do you separate generator, battery, and RF so noise and safety problems don't stack up?

ci_cover.jpg

I'm sketching a baseline layout for a 24-hour EMCOMM-style field station and want to pressure-test it before it becomes a standard kit. The goal is one operating position under a pop-up canopy with an HF rig (100 W class), a dual-band VHF/UHF rig, a laptop for logging and digital modes, and lighting. The power plan is a LiFePO4 battery as the primary source, solar as a trickle or daytime supplement, and an inverter generator as backup for recharging and heavy loads.

Here is the draft. The generator sits at least 20 feet from the shelter, with its exhaust pointed away from the tent and the operating position, and a battery-powered CO alarm inside. The battery feeds a fused distribution block with Anderson Powerpole outputs, and each radio gets its own fused leg. HF is a end-fed or center-fed wire on a telescoping fiberglass mast, with a 1:1 current choke at the feedpoint and another at the radio end of the coax. VHF/UHF is a separate antenna on its own short mast, kept clear of the canopy frame. Coax and power lines leave the tent in different directions and cross at 90 degrees if they have to cross.

The things I'm least sure about are these. First, how much battery capacity is realistic? My rough math is watt-hours = volts x amp-hours, so a 100 Ah LiFePO4 at 12.8 V nominal is about 1,280 Wh. That's before BMS limits and keeping some reserve, and I'd want to measure the actual receive and transmit current of the rigs rather than trust spec-sheet peaks. Second, whether solar charge controllers and the generator are likely to be the dominant noise sources on HF, and what the best way to find out is before a real deployment. Third, what grounding actually belongs in a temporary station, since I keep seeing very different advice.

What would you change? I'm especially interested in the failure modes that only show up after a few hours: voltage sag, heat, wind, fuel logistics, and operator fatigue.

  • Replies 2
  • Views 40
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the power side, the first thing I'd do is write down a load budget instead of relying on battery size alone. Take the receive current of each radio, the transmit current at your actual power setting, the laptop, lights, and any charging loads. Then apply a duty cycle that matches the mode. SSB voice and FT8 are very different loads, and a 100 W digital mode at full power for long stretches can heat a rig and drain a battery much faster than casual voice. Many operators run digital modes at reduced power to protect the radio and the battery. Check your rig's manual for its continuous-duty rating.

For LiFePO4, check three things. Does the battery's BMS have a low-voltage cutoff, and what happens to your radios when it trips? An abrupt cutoff in the middle of a net is a bad surprise, so a voltage display or low-voltage alarm on the distribution panel is worth having. Is the BMS's continuous current rating comfortably above your worst-case load? And does your charging path match the chemistry? Use a LiFePO4 profile on the MPPT controller or generator-fed charger, and keep in mind that most LiFePO4 cells shouldn't be charged below freezing unless the battery has low-temperature protection or heating. Also confirm your radios tolerate the voltage range the battery presents, since a fully charged pack sits higher than a lead-acid resting voltage.

Fuse the positive lead close to the battery, size wire for voltage drop and not just ampacity, and keep high-current runs short. A loose or undersized Powerpole connection can cause intermittent TX problems that look like RF issues. If your group standardizes on Powerpoles, agree on the polarity orientation convention in advance so mixed kits from different people don't get cross-connected.

For the generator, treat it as a charger and a backup, not the primary source for the radios. Inverter generators produce a cleaner waveform than conventional ones, but the electronics, eco-throttle behavior, and cabling can still radiate noise. Test it both ways: eco mode on and off, with the radio on battery while the generator charges, then with the radio on the generator-fed supply. Place it downwind, keep fuel stored safely away from it, let it cool before refueling, and never run it inside or under the shelter.

  • Moderators

On the RF side, I'd structure the setup so you can diagnose noise one source at a time. Before any deployment, do a baseline noise check with everything off except the radio on battery, then add loads one at a time: laptop, charger, solar controller, generator, LED lights. Cheap LED lanterns, USB chargers, and switching supplies are often the worst offenders, and they can easily be worse than the generator. A short AM or SSB listening test on a couple of bands, and noting S-meter changes, tells you more than guessing. Ferrite chokes on DC leads, USB cables, and the antenna coax are cheap to try, but treat them as experiments you verify, not magic fixes.

On grounding, keep the concepts separate. Electrical safety grounding applies to the generator and any AC distribution: use GFCI protection, proper cords, and never backfeed anything into a building. Know whether your generator bonds neutral to frame, and follow the manual. RF grounding is different. A vertical or end-fed antenna may need a counterpoise or radials to work well, and a single short ground rod does not make a station lightning-safe. If thunderstorms are nearby, the safest plan is to stop operating, disconnect antennas, and take shelter. A temporary static or equipment bond can reduce shock and RF-in-the-shack issues, but don't describe it as lightning protection in your procedures.

For masts, the main hazards are wind and power lines. Pick a site where a falling mast and antenna can't reach any overhead line, guy it appropriately for the conditions, and keep people away from the fall zone. A pop-up canopy with a metal frame can detune or shadow antennas, so keep the wire and especially the VHF/UHF antenna clear of it, and weigh down or stake the canopy legs for gusts. On coax, loss matters most at VHF/UHF, so use low-loss cable for longer runs there. At HF, a typical field run is less of a loss problem than common-mode current. Keep jumpers short, weatherproof outdoor connections, add strain relief, and keep coax away from power cables and the generator.

Finally, put it all on a checklist with a teardown half. Setup: site and wind check, overhead hazards, generator placement and CO alarm, shelter anchoring, antennas and chokes, power distribution, noise baseline, comm check, log started. Teardown: stop transmitting, power down, disconnect antennas before lowering masts, coil coax, count stakes and guy lines, check the site for trash and fuel spills, and recharge or inventory batteries. If this is for a served agency, also write down the frequency plan, check-in schedule, and message-handling format ahead of time so the station design supports the mission.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.