Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Repeater basics that trip people up: offsets, tones, linking and etiquette (what would you add?)

ci_cover.jpg

Many repeater problems come down to a few settings or habits that nobody explained. This thread is a starting point for a shared checklist, and corrections are welcome. Rules and band plans differ by country, so check your own regulator and regional coordinating body.

Offsets. A repeater receives on one frequency (its input) and transmits on another (its output). Your radio listens on the output and transmits on the input, so you set a shift or offset. On 2 m in the US, outputs from about 146.61 to 146.97 MHz use a negative shift (-600 kHz), and outputs from about 147.00 to 147.39 MHz use a positive shift (+600 kHz). On 70 cm the split is usually 5 MHz, but the direction depends on the sub-band and region. Many radios have an automatic repeater shift feature, but it only guesses from a band plan, so confirm it against the listing for the repeater you actually want.

CTCSS, PL and tone squelch. CTCSS is a sub-audible tone, roughly 67 to 254 Hz, sent along with your voice. PL is Motorola's trade name for the same thing. Many repeaters need the correct tone on your transmission before they open. That is the access tone, and your radio's plain "Tone" mode sends it. Some repeaters also send a tone on their output. If you set your radio to tone squelch (often labeled TSQL), it will only open its speaker when it hears that tone, which keeps you from hearing other users on the same channel. It does not stop interference, though. The repeater is still receiving everyone, and you just can't hear them. A repeater may need different tones for access and for output, so check the listing for both.

DCS. Digital Coded Squelch does the same job as CTCSS using a three-digit octal code (such as D023N) sent as a low-speed data stream. Both ends have to agree on the code and the polarity (N or I), and mismatched polarity is a common reason a DCS repeater won't respond. Neither CTCSS nor DCS is security or privacy.

Time-out timers. Most repeaters have a time-out timer (TOT) that drops the transmitter if a single transmission runs too long, often somewhere between one and three minutes. Leave a pause between transmissions so someone can break in and the timer can reset. If the repeater has a courtesy tone, wait for it before you key up again.

Linked systems. Linking adds delay, and the delay changes how you should operate:

EchoLink connects through the internet to nodes and conference servers, and users are verified by callsign. AllStarLink uses Asterisk-based nodes that can be linked to hubs and other nodes. IRLP uses dedicated nodes and DTMF node numbers. Wires-X is Yaesu's system for System Fusion, with nodes and rooms. DMR uses two timeslots and color codes, and you reach other repeaters through talkgroups. You also need a DMR ID for your radio, and a codeplug that matches the repeater's color code, timeslot and talkgroups. D-STAR uses callsign routing with fields such as MYCALL, URCALL and RPT1/RPT2, and it connects repeaters through reflectors. Check the club's page for which of these a given repeater supports, because it can change.

Etiquette. Listen before you transmit, since you may be on a linked system and the other side may be mid-conversation. You don't need to say "CQ" on a repeater. Give your callsign and say you are listening, or break in if there is a conversation. Keep transmissions short, and identify as your licence requires. In the US that means at least every ten minutes and at the end of a communication, but check your own country's rules. Avoid kerchunking, which is keying up just to see if you hit the repeater. Say your callsign instead, or use a local test or echo node if there is one.

Open versus closed, coordination, clubs and directories. An open repeater is available to any licensed operator, while a closed repeater limits use to members or approved users, and that is the owner's call. Open still doesn't mean anything goes, because the trustee or control operator can impose rules. Coordination is handled by a regional body that assigns frequencies and tone pairs to reduce interference, and in many areas coordinated systems get recognized protection. Repeaters usually cost money for tower space, power, links and repairs, so clubs often depend on dues and donations. Directories like RepeaterBook, ARRL listings and club websites are useful, but they can go stale, so double-check a repeater's frequency, tone, status and linking before relying on it.

What would you add? Is there a setting or habit you wish a new operator knew from the start?

  • Replies 2
  • Views 52
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Good list. I'd add that reverse (or "reverse offset") is one of the most useful features for new operators. It swaps your transmit and receive frequencies so you can listen on the repeater's input. If you can hear the other station well on the input, you can probably talk simplex and free up the repeater. If you can't hear them there, a repeater is the right choice.

One more tone issue: some repeaters need the access tone only on your transmit side and send no tone on their output. If you turn on tone squelch for that repeater, your radio will stay muted. In that case you set the "Tone" (encode) value, not the decode value, so check what your radio's tone mode actually does.

For DMR, color code and timeslot mismatches look just like a dead repeater, because you can key up and nothing comes back. If you can't get in, check those and the talkgroup before you decide the repeater is down.

  • Moderators

On linked systems, I'd stress that a linked repeater has a longer pause before someone can answer, and another node may be transmitting to a different part of the network. Wait a beat after you unkey and again after the courtesy tone before talking again. Don't transmit over a net or a call you can't hear, since other nodes may be carrying it. Announcing the callsign of the person you are trying to reach helps because the audience could be across several systems.

On D-STAR and Fusion, reflector and room connections can change who hears you. Before a long conversation, ask whether the system is connected to a reflector or room. The same goes for AllStar and EchoLink nodes: if the repeater is linked to a node or conference, say what you want to do before you start. In many areas a repeater club will have written rules or a link-control procedure for this, so read those first.

Finally, the trustee or club is a better first call than the repeater itself if you find a problem. A stuck PTT, a wrong tone listed online or a link stuck in the wrong state are easy for them to fix once they know. Many clubs have a contact address on their site or on the directory entry.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.