Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning an HF shack around the whole signal chain: rig choice, power, filtering and bonding

ci_cover.jpg

Rig comparisons usually stop at the spec sheet: IC-7300 vs FT-991A, FTDX10 vs TS-590SG, K3S vs TS-890S. But a lot of what makes a station pleasant or frustrating sits outside the radio. That includes the feedline and common-mode current, the power supply under transmit load, the amp and tuner arrangement, and how the equipment is bonded. I'd like to compare notes on how people plan the whole chain.

Rig class and what it implies for the rest of the shack. The 100 W class covers the IC-7300, IC-7610, FT-991A, FTDX10, TS-590SG, TS-890S and K3S. All of them want a well-regulated supply of about 13.8 V that can hold voltage at roughly 20 A or more on SSB or CW peaks. At the other end, the Xiegu G90 (about 20 W, built-in ATU) and the KX3 (low power, very compact) are often used portable or in small shacks. They put less demand on the supply, but they are no less sensitive to feedline problems, RF in the shack, or noise from cheap switching supplies.

Receiver architecture is a planning variable. The IC-7300 and IC-7610 use direct-sampling SDR front ends. The FTDX10 uses a hybrid approach. The TS-590SG, TS-890S and K3S are superhet designs with roofing filters. Each can be excellent, but they handle strong out-of-band signals differently. If you have a second operating position, a neighbor's transmitter, or a contest-style multi-radio setup, band-pass filters on the receive path (or between rig and amp) can matter. For one rig on one antenna, an external filter may be unnecessary. It's worth working out the actual interference scenario before buying hardware.

Amplifier and tuner placement. A common arrangement is rig, then amp, then external tuner, then feedline. The internal ATU in a rig (or the G90's) usually has a limited matching range and sits at the shack end, so it can only make the rig see a good load. It does nothing about loss or radiation in a high-SWR feedline. If you use an amp, make sure the band data or keying line is wired correctly and that drive power is set below the amp's rated input, so you aren't relying on the amp's protection to catch mistakes. Tune at low power into the tuner before keying the amp.

Grounding and bonding: three jobs that get conflated. There is (1) electrical safety, meaning mains equipment grounds; (2) lightning protection, which is mostly about equipotential bonding and a safe path for surge energy; and (3) RF behavior in the shack, which is mostly about preventing common-mode current on cables. A ground rod by itself does not make a good "RF ground" for a typical station. A common approach is to bring coax in through an entry panel or bulkhead, bond that to a ground rod outside, and bond that rod to the building's electrical service ground. Local electrical codes and your AHJ define exactly how, so check them. Inside the shack, a bonding bar tying equipment chassis together is common, but it shouldn't replace choking the feedline.

Layout details that cause real problems. Keep DC leads short and heavy-gauge, and fuse the positive lead. Separate power cables from audio and USB where practical, and put ferrites or chokes on USB, CAT, and audio lines if you see RFI. Put a common-mode choke on the coax near the shack entry and at the antenna feedpoint if the antenna type needs one. Label the cables, because troubleshooting RFI is much easier when you can pull one connection at a time.

Questions for the thread: what would you prioritize first on a limited budget, a better power supply, a feedline choke and entry panel, or a filter? And do you build a shack around one rig for everything, or around separate receive and transmit paths?

  • Replies 2
  • Views 44
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

If budget is tight, I'd put feedline and bonding ahead of almost any piece of radio hardware. Many "my rig has noise or RFI" problems turn out to be common-mode current on the coax, on USB cables, or on the mains wiring. A proper choke at the shack entry is cheap compared with replacing a radio, and it helps whichever rig you own. A good 13.8 V supply with low ripple is next, because a switcher that radiates hash into a sensitive receiver will undermine even a top-tier TS-890S or IC-7610.

For the tuner, I'd separate two goals: making the rig see a safe SWR, and making the antenna system efficient. A tuner solves the first one. If a doublet or a long wire needs a tuner, it's usually better to put the tuner close to the feedpoint, or use ladder line to the shack, than to push a high-SWR coax run through it.

  • Administrators

I'd add a caution on filters. Band-pass filters are very useful when you have a specific problem, like two stations on the same band or a strong nearby transmitter, but they add insertion loss and another point of failure. Don't put one in the path of a rig or amp unless it is rated for the power and the SWR it will see. A filter that handles 100 W into a good match may not survive a high-power amp into a poor match.

On the single-rig vs multi-rig question, a single 100 W transceiver is simpler, but a second receiver, whether an IC-7610's dual receive or a separate receiver, can be handy for DXing or split operation. Whatever you use, plan where RF will flow. Antenna switch grounding, a clean station ground bar, and a clear antenna lightning disconnect procedure matter more than which logo is on the front panel.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.