From FM birds to linear: how to structure your first month of satellite operating (Doppler, tracking, antennas, QO-100)
- Replies 2
- Views 42
- Created
- Last Reply
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
A lot of people get started on amateur satellites with a handheld and an Arrow-style antenna, then hit a wall when they try to move up to linear birds like RS-44. This thread is meant to lay out a sensible progression and collect practical tips. Corrections and additions are welcome.
Step 1: Learn to predict passes, not just hear them. Install Gpredict (or SatPC32 on Windows) and enter your location. Set your Maidenhead grid square properly, at least 6 characters (e.g. a format like AB12cd), and keep your system clock accurate. Update the Keplerian elements (TLEs) regularly, because stale elements make the predicted AOS time and Doppler offset drift. Look at max elevation as well as pass time. A 10° pass is brief and noisy, while a 60°+ pass gives you far more usable time. Also watch the azimuth path, since it tells you where to start pointing.
Step 2: Start with FM birds. FM satellites such as AO-91, AO-92 and SO-50 work like fast-moving repeaters with a single channel, so many people start there. Requirements vary by satellite. SO-50, for example, has historically needed a CTCSS access tone and an arming sequence before the repeater is active. AO-91 and AO-92 have used a different CTCSS tone setup. Check the current AMSAT status pages for frequencies, tones, and whether a given satellite is operational, because satellite status and schedules can change. Don't rely on memorized numbers.
On FM you are working in V/U or U/V split, so you transmit on one band and receive on the other. Full duplex helps a lot: if you can hear your own downlink while transmitting, you can tell whether you are actually getting into the bird. With a handheld, a headset or earpiece is the cheap way to keep your own transmitted audio from feeding back into the mic.
Step 3: Understand Doppler. For a typical LEO pass, Doppler shift is a few kHz on 2 m and roughly three times that on 70 cm, since it scales with frequency. It starts high on the approach (the downlink sounds higher than nominal), passes through zero at closest approach, and ends low. On FM you typically correct in 5 kHz steps, starting a bit high and walking down. Programs like Gpredict can drive the radio through CAT control, but many operators still do the correction manually on the first few passes to understand what is happening. Know which side of the link you correct: ideally you adjust the uplink so the signal arrives at the satellite on its nominal frequency, and then tune your receiver to follow the downlink.
Step 4: Antennas and pointing. A handheld Yagi such as an Arrow-type 2 m/70 cm antenna works well for LEO. Hold it with the elements in line with the satellite's path and keep it pointed at the bird. Polarization mismatch and fading are normal. Some people rotate the antenna slowly to track signal peaks. For fixed stations, a pair of crossed Yagis on an az/el rotator is the usual next step, with circular polarization if you want to reduce fading. Rotators need good calibration, and your tracking software should read back from the rotator rather than assuming it has reached the commanded position. Note that for passes passing near the zenith the azimuth can swing very fast, so consider the rotator speed limitations.
Step 5: Linear transponders (SSB/CW). RS-44 is an example of a linear transponder satellite. Unlike FM birds, it relays a whole slice of spectrum, so several stations can be heard at once. Most linear satellites in the amateur service are inverting, meaning that if you tune your uplink up, the downlink goes down. This is essential for Doppler correction, and tracking software handles it. Keep power modest: if your signal on the downlink is louder than the beacon, you are probably running too much power. The best operators tend to hear their own signal at about the same level as the beacon. Also, in CW and SSB, you need to be on frequency within a few hundred Hz to be easily readable, so automatic frequency control from software like Gpredict or SatPC32 is much more useful here than on FM.
ISS notes. The ISS has carried an APRS digipeater and a voice repeater at various times, and operations are not continuous. They may be switched on or off, or change configuration. Before trying, check the current operations announcements. APRS via the ISS is a packet mode, so follow its guidelines about keeping transmissions short and not overusing the uplink.
QO-100. QO-100 is different from the LEO satellites because it is geostationary. There is no pass prediction and essentially no Doppler to correct. You point a dish once. It has a narrowband linear transponder (SSB/CW) and wideband for digital video. The uplink is on 2.4 GHz and the downlink on 10 GHz, so the main challenges are the dish and feed, LNB stability (drift is the normal problem, typically handled with a GPSDO or a stable locked LNB), and keeping the uplink power in check. Because the satellite is always in view from large parts of its footprint, it can be a good place to practice linear operating discipline.
Questions for the thread: what sequence worked well for newcomers to move from FM birds to RS-44? Which tracking software settings do you recommend for beginners with only one radio? And how do you decide whether to buy a rotator or just keep hand-tracking with an Arrow?
Link to comment
https://www.hamradiobase.com/forums/topic/10827-from-fm-birds-to-linear-how-to-structure-your-first-month-of-satellite-operating-doppler-tracking-antennas-qo-100/Share on other sites