Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead or sick rig on the bench: a practical order of attack for no TX, no RX, noise and protection faults

ci_cover.jpg

Most repair threads start with "it's dead, what's the part?" The fastest fixes usually come from narrowing the fault before any cover comes off. This is a working order of attack for no transmit, no receive, noise, SWR protection trips and suspected blown finals. Add to it, or tell me where you'd change the order.

Step 0: rule out the boring stuff. Check the fuse in the DC cable, polarity, and the plug and socket. Then check the settings: TX inhibit, a stuck PTT or accessory line, a mic gain or menu setting, squelch, RIT/XIT, split, attenuator or preamp, and a mode that doesn't match what you expect. Test on a dummy load and a known-good antenna. A lot of "no receive" faults turn out to be a bad feedline or a shorted antenna jack.

Step 1: the power supply and the DC path. Measure voltage at the rig end of the cable, not just at the supply terminals, and measure it while the rig is trying to transmit. A supply that reads 13.8 V unloaded and sags to 10 V on TX will produce symptoms that look like a dead PA or a protection fault. Check the polarity protection diode or fuse, the internal fuses, and the regulated rails (typically 5 V, 8 V, 9 V and so on) against the service manual. If the supply is a switcher, remember that it can also be the source of your noise.

A current-limited bench supply is a cheap way to avoid turning a small fault into a large one. Start with the limit low and raise it while watching idle current against the manual's figures. If idle current is far too high with no drive, stop and find out why.

Step 2: no receive. Work from the speaker backwards, or from the antenna forwards, but pick one and stay with it. A simple audio check is to touch a finger or a screwdriver to the volume control wiper or the audio amp input. If you hear a buzz, the audio stage and speaker are probably alive and the fault is earlier. If there is no hum, check the audio IC supply and the speaker jack switching contacts.

For the RF side, confirm that the oscillators are running and the PLL is locking (a scope or frequency counter helps here), that the T/R switching is going to RX, and that the front-end signal path is intact. Check the antenna relay or PIN diode switching, bandpass filter relays, and any attenuator relays. A signal generator at a known level through the chain tells you where the signal disappears.

Step 3: no transmit. Split it into three questions. Does the rig go into TX (relay click, TX line goes high, rails switch)? Is there drive from the exciter stage? Is the PA biased and drawing current? A scope with a 50 ohm load and an RF probe, or a power meter, shows quickly whether the signal dies at the driver, the predriver or the PA.

Step 4: SWR protection and foldback. If power folds back or the rig reports high SWR on a dummy load, the problem is more likely the detector than the antenna. Suspects include the forward and reflected diodes, the bridge or directional coupler (cold joints on the toroid, a cracked trimmer), the reference voltage, and the connector or coax jumper inside the rig. A common source of confusion is that the protection circuit can be working properly because something downstream really is wrong, such as a PA stage that has gone out of balance. Compare forward and reflected readings against the manual before touching any trimmers.

Step 5: blown finals. The transistor is nearly always the symptom, not the cause. Before you fit new ones, check for a shorted bias network, a failed driver, bad emitter or source resistors, a defective output filter, high supply voltage, parasitic oscillation, and poor thermal contact. Use the same type, or a manufacturer-approved replacement with the same bias and gain behaviour. Don't assume an apparently equivalent device will behave the same at the same bias. Set bias with no RF drive, with a current-limited supply and a dummy load, using the manual's procedure, and use fresh thermal compound on a clean, flat heatsink.

Step 6: noise. First decide whether the noise is external or internal. Run the rig from a battery or a known quiet supply, disconnect the antenna and fit a dummy load, and see if the noise changes. If it disappears on battery, the supply or the mains wiring is the source. If it stays, look at the rig itself, including dried electrolytics on internal rails, a loose shield or ground strap, a dirty shielded connector, and a failing regulator. Turn off any noise blanker or DSP while testing so you aren't hiding or creating symptoms.

Capacitors and contacts. Electrolytics age, and leaking SMD electrolytics can damage nearby traces. Use the same voltage rating or higher, the correct polarity, and low-ESR types in power rails and switching circuits. After removing a leaker, clean the board thoroughly with isopropyl alcohol and a brush, and inspect the traces for damage. For switches, pots and connectors, use a contact cleaner rated for electronics sparingly, and avoid soaking anything near plastics, encoders or trimmers. Reflowing a suspect joint is often more useful than spraying a cleaner at it.

Alignment. Alignment fixes drift. It shouldn't be the first response to a dead stage. Use the service manual's procedure, the specified test equipment, and the right order of adjustments. Note the original positions of any trimmers and cores before you change them.

Test equipment that earns its place: a decent DMM, a current-limited bench supply, a dummy load and power meter, a scope (even a modest one), an RF probe, a signal generator, a frequency counter and an ESR meter. The service manual with schematic and voltage tables matters as much as any of these. Mains-powered supplies and tube-based rigs hold lethal voltages, so discharge capacitors, use an isolating approach where appropriate, and don't work alone on live high-voltage circuits.

What's your usual first move when a rig comes in with a vague "it stopped working" description? Do you go to the supply, or to the antenna path first?

  • Replies 2
  • Views 38
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The current-limited supply point deserves emphasis. Watching idle current while you bring the voltage up gives you information before you see any smoke. If current jumps well above the manual's idle figure with the drive removed, you've learned the fault is in the DC or bias path, not the RF path, and you've kept the damage down.

On the scope, one habit is worth building: look at the supply rails with AC coupling and a short ground spring while the rig is in both RX and TX. Ripple that looks tolerable on a meter can be nasty on a scope, and a rail that collapses for a few milliseconds when the relay clicks can explain odd resets or a PLL that won't lock. I'd also put a DC-blocked probe on the PLL tuning voltage when the symptom is no RX or no TX only on some bands, since an unlocked VCO often gives a very clear clue there.

  • Moderators

I'd tweak the order a little. On the "clean the contacts" advice, I'd reflow and inspect before spraying anything on a rig that behaves intermittently. Contact cleaner can temporarily cure a symptom and hide a cracked joint or a failing connector that returns later. It's good for dirty switches and pots, but with relays, trimmers and board-to-board connectors, look first and work out which contact is bad.

On SWR protection, one useful test is to put a dummy load on and measure the forward and reflected detector voltages at a low, safe power level. A properly terminated load should give a reflected reading near zero. If it doesn't, the bridge or detector is suspect. If the reading is fine at low power but protection trips at higher power, look at the PA output stage, the low-pass filter relays and any component that changes behaviour when heated. In blown-finals cases, check the driver stage and the bias network before you order a matched pair, because replacing the transistors without finding the cause often just repeats the failure.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.