Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a Wire Antenna from Scratch: Wire, Insulators, Chokes, Feedline and Modeling Before You Cut

ci_cover.jpg

This thread is for the practical decisions that come up when you build a wire antenna from scratch rather than buying one. The example is a simple one: a half-wave dipole for 40 m, possibly extended later to a fan dipole or a ladder-line-fed doublet. The same questions apply to verticals and trap designs, so let's go through them in order.

Start with the wire. For a permanent span, 14 AWG hard-drawn copper or copper-clad steel is a common choice because it resists stretching. Soft-drawn copper stretches over time and the antenna slowly gets longer and resonates lower. Stranded insulated wire is easier to handle and coil, and 16 to 18 AWG is fine for shorter spans or portable use. Insulation adds capacitance along the wire, so an insulated dipole typically resonates a few percent lower than the bare-wire formula predicts. The usual starting point is about 468 divided by the frequency in MHz, which gives feet for the whole dipole (about 142.6 divided by f for metres). Treat that as a starting length only. Cut the wire long, then trim in small steps while measuring.

Insulators matter more at the ends than most people expect. Each end sees high RF voltage and mechanical load. UV-stable plastic, glazed ceramic, or properly rated acrylic or polycarbonate work well. A knotted loop of rope is not an insulator once it is wet and dirty. Use non-stretch rope such as polyester, or Dacron-type line, for supports, and consider a pulley or a weighted line at one end so tree movement does not snap the wire. At the center, relieve the strain so the coax weight does not pull on the solder joints. A solder joint on stranded wire becomes brittle at the edge of the solder, so make the mechanical connection first and seal it against moisture afterwards.

Then there is the feedline problem. A dipole is a balanced antenna, and coax is unbalanced. Without a choke or balun, current can flow on the outside of the coax shield, which distorts the pattern, lets RF into the shack and makes SWR readings change when you move the cable. A 1:1 current balun at the feedpoint is the usual fix. A choke made from several turns of the coax itself through a suitable ferrite core, typically type 31 or 43 material for HF, is a common alternative. The ferrite mix needs to suit the band, because the choke has to present high impedance at your operating frequency, not just something that looks like a lot of ferrite. For ladder-line feeds into a tuner, the balun usually goes at the tuner end, and the line should leave the antenna as symmetrically as possible.

On the vertical side, the key point is that the radial system is half the antenna. A quarter-wave vertical over a few elevated radials behaves very differently from the same element sitting on a handful of short wires lying on the soil. Elevated resonant radials, ideally at least four, are a reasonable compromise, and drooping them downward moves the feedpoint resistance toward 50 ohms. Ground-mounted systems usually want many more radials, and length matters less than count. Fiberglass poles make good vertical supports, but check that the pole is not carbon fiber, since carbon is conductive and can interact with the antenna.

For measuring, an antenna analyzer or a VNA at the feedpoint gives the clearest picture. Measuring SWR at the transmitter end with long, lossy coax can hide a bad match because the cable loss improves the apparent SWR. Also remember that a low SWR does not mean an efficient antenna. A dummy load has an excellent SWR and radiates nothing.

Before cutting any wire, you can model the design in EZNEC or MMANA-GAL. Both help you find approximate resonant length, feedpoint impedance, take-off angle and the effect of height over ground. The usual pitfalls are too few segments, a poor ground choice, and wires meeting at awkward angles. MMANA-GAL has an average gain test that is a useful sanity check on whether the model is behaving. Neither program knows about common-mode current on your feedline unless you add it to the model, so a clean-looking pattern is not a guarantee.

What are you building first, and which of these steps has caused you the most trouble: the mechanical side, the feedline, or getting the model to match reality?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing I'd add on trap antennas, since you mentioned them: a trap is just a parallel LC circuit that acts like an insulator at its resonant frequency, so the antenna looks shorter on the higher band. That also means each trap has to handle real voltage and current, and the components need to be rated for your power level. The coil Q sets the losses, and capacitor dielectric matters. Low-loss capacitors such as NP0/C0G ceramic, mica or properly rated coax-stub traps are the usual routes. The wire between traps is also shorter than the free-space length would suggest, because the traps look inductive below their resonance and shorten the physical length needed. That is why a trap dipole rarely follows the plain formula.

The practical way to tune a trap is to measure it on its own, with a small loop coupled to an antenna analyzer or a grid-dip-type setup, and set it to the target frequency before it goes into the antenna. Then trim the end sections for the lower band and check the upper band separately. The trade-off is narrower bandwidth and some loss compared with a single-band dipole. A fan dipole or a simple resonant dipole per band fed from one coax avoids trap loss entirely, though the elements interact and need spacing and a bit of trimming.

  • Moderators

On the modeling side, the part that trips people up is believing the numbers to more precision than the model deserves. The main check I'd suggest is a convergence test. Double the segments per wire and see if the feedpoint impedance changes significantly. If it does, the model isn't settled. In EZNEC, also try the same antenna over a couple of different ground types, because feedpoint resistance and take-off angle for low horizontal wires change noticeably with soil conductivity and height. For a dipole at, say, a quarter wave or lower, the pattern is heavily dominated by height, which is why NVIS-style high-angle radiation is common on low 80 m and 40 m dipoles.

For verticals, model the radials explicitly. A perfect-ground vertical model will show gain figures that real installations seldom match. Compare ground-mounted radials against elevated radials, and see how the efficiency estimate and feedpoint resistance change. In MMANA-GAL, remember that its wire loss and ground settings are separate from your insulation or velocity-factor effects, so you will usually still end up trimming the real antenna. Use the model for choosing the structure, spacing and approximate dimensions, then use the analyzer to find the final length. If the real antenna resonates far from the model, check for nearby metal, coax routing, an uncorrected end effect from insulators, and whether the feedline choke is actually working.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.