Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

EME from 2 m to 10 GHz: station requirements, JT65/Q65, polarization, libration and sked planning

ci_cover.jpg

This thread is meant to pull together what a station realistically needs for moonbounce on each band, and how the operating side (modes, polarization, timing, tracking) fits around the hardware. Numbers below are approximate and meant for planning. Check them with an EME calculator before building anything.

Start with path loss, because it drives everything else. Averaged over the Moon's distance, the round-trip loss is very roughly 252 dB on 144 MHz, 261 dB on 432 MHz, 271 dB on 1296 MHz and close to 290 dB on 10 GHz. The Moon's distance varies from about 356,000 km at perigee to about 407,000 km at apogee, which changes the loss by around 2 dB. That is why planners show a distance "degradation" figure for each date. The round-trip delay is roughly 2.4 to 2.7 seconds, so you hear your own echo a couple of seconds after you stop transmitting. That echo is the most useful test of the whole station.

Rough starting points by band, assuming digital modes and working the larger stations:

2 m: the usual entry is several long Yagis in a phased array, or one very long boom if you can accept a smaller signal. Power is typically up to the legal limit. Sky noise is high on this band, and Faraday rotation is strong. 70 cm: a bigger array (often 4 to 8 or more Yagis) or a dish of a few metres. Rotation is much less than on 2 m but still present. 23 cm: a dish of roughly 2.4 to 4 m is the common route. A 3 m dish at 55% efficiency gives about 29 to 30 dBi, with a beamwidth of about 5 degrees. Above 3 GHz and up to 10 GHz: dishes again, and pointing accuracy becomes the main challenge. A 1.8 m dish on 10 GHz has about 1 degree of beamwidth, and the Moon is only about 0.5 degrees across.

What are people's views on where the real minimum is on each band? I'd like to separate "can hear your own echoes" from "can complete a contact with typical stations", since those are different bars. Please add anything on preamps, feedline losses, tracking accuracy and polarization handling, since that's where small stations often lose their margin.

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the low bands I'd put receive noise first, because 2 m and 70 cm EME is often limited by how well you hear rather than how much power you run. Mount a low-noise preamp at the antenna or feedpoint, with a sequenced low-loss relay, and use a noise figure that is well under 1 dB. Every few tenths of a dB of loss ahead of that preamp counts directly against the weak echoes. A long run of ordinary coax with a relay at the shack end can cost you more than a bigger array would give you. Sequencing matters just as much on transmit. The relay should switch before the PA is keyed, and the PA should be unkeyed before the relay releases, otherwise you can damage the preamp or the relay.

On polarization, the two effects get mixed up. Faraday rotation is rotation of linear polarization in the ionosphere. It is strongest on 144 MHz, fades with frequency, and varies over minutes and with the time of day. Spatial polarization offset is geometric and depends on where the two stations are relative to the Moon. It can be large when the stations are far apart in longitude. The practical fix on 2 m is an array that can change polarization, such as a rotatable boom, switchable crossed Yagis, or at least an ability to select horizontal, vertical or the two combined. Many stations simply wait for a better moment, and that is a legitimate option. At 1296 MHz and above, rotation is small enough that people usually switch to circular polarization. The reflection reverses circular sense, so the groups on those bands agree on a convention for which sense is sent and which is received. Confirm it with your sked partner before you blame the antenna.

Before any contacts, measure the system. Sun noise and Moon noise measurements, plus your own echoes in WSJT-X, tell you more than a spec sheet does. If you cannot hear any of your own echoes, a contact with a similar station will not happen either.

  • Moderators

I'd add the operating side, because even a good station can waste a lot of time if the setup is wrong. For JT65 and Q65, the tone spacing is set by a submode letter. Wider submodes tolerate more spreading, but they cost some sensitivity. Libration is the Moon's slow rocking, which spreads the echo in frequency and gives fast flutter fading. The spread grows with frequency, from a fraction of a hertz on 2 m to tens of hertz at 10 GHz. This is why the common choice moves from narrow submodes on 2 m towards wider ones on 23 cm and the microwave bands. The exact letter used on each band is set by local practice and by the WSJT-X documentation, so read the current guide and ask on the chat page rather than trusting my summary. Q65 is generally regarded as more tolerant of spread and fading than JT65, and it uses ordinary full messages. JT65 has the shorthand messages for confirming a QSO.

For sked planning, check the window when the Moon is above the horizon for both stations. You also want the Moon away from the galactic plane and the Sun where possible, because sky noise rises with both. A planner such as the VK3UM EME calculator, or the astronomical data in WSJT-X, will give you a combined degradation figure. Agree beforehand on the band, mode and submode, the frequencies, and who transmits in the first period. Allow a few minutes of echo testing or alignment before starting.

On tracking, work out what your pointing accuracy actually is before you buy a rotator or build a mount. For a dish, take the beamwidth as about 70 times wavelength divided by diameter, in degrees, and you will want to be accurate to a fraction of that. A tracking error that is invisible on 2 m can drop you out of the beam on 10 GHz. Use software that applies Doppler correction, and check the dish's pointing against the Sun (for solar noise) or the Moon itself. Also keep a log of what actually worked on each sked, because that is what will help you plan the next one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.