Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot, HOA, no tower: how do you rank EFHW, OCFD, doublet, vertical and loop options by actual performance, not just SWR?

ci_cover.jpg

Take a typical constrained scenario: a 50 x 100 ft lot, a couple of tall trees, a neighborhood that doesn't welcome visible antennas, and a 100 W station that wants 80 through 10 m. The usual candidates are an end-fed half-wave (EFHW), an off-center fed dipole (OCFD), a G5RV or a doublet on ladder line, a ground-mounted or elevated-radial vertical, and a magnetic loop. Each gets recommended with a different argument, and the arguments often confuse SWR with performance.

The first point worth settling is that SWR only tells you how well the load matches the line at one point. A dummy load gives a perfect 1:1 and radiates nothing. A short loaded antenna over poor ground can show a flat match and still lose most of the power as heat. SWR matters for protecting the rig, for avoiding extra feedline loss, and for avoiding tuner stress. It says little about gain or takeoff angle.

Feedline loss is where SWR does matter. Coax loss is quoted for a matched line and rises with mismatch. Roughly, RG-213 loses around half a dB per 100 ft at 14 MHz when matched, and RG-58 loses about twice that. On 10 m the figures are higher still. A doublet at 3.5 MHz with a 10:1 SWR on a long run of thin coax can lose far more than expected. That's why doublets and G5RV-style antennas are normally fed with ladder line, with the transition to coax made through a tuner and a choke near the shack, so that the high-SWR section is the low-loss one.

Common-mode current is the other recurring problem. EFHWs, OCFDs and G5RVs all tend to put RF on the coax shield unless it's choked. The EFHW makes the shield part of the counterpoise by design, since the feedpoint is at a high-impedance voltage maximum, usually through a 49:1 or 64:1 transformer. A choke at the radio end, and sometimes a short counterpoise at the transformer, often cures RFI and the 'SWR changes when I touch the coax' symptom. An OCFD feeds at about a third of the length through a 4:1 current balun. It works well on its fundamental and harmonically related bands, and it is usually weaker on the WARC bands.

Height is the thing people underrate. A horizontal dipole at 30 ft is about 0.21 wavelength high on 40 m, which suits regional work but pushes much of the energy to high angles. On 20 m it's about 0.43 wavelength, and the pattern is much better for DX. On 80 m, any wire at that height behaves as a high-angle NVIS-type radiator. For an inverted V, keep the apex as high as possible, keep the included angle reasonably wide (above roughly 90 degrees if you can), and keep the ends well out of reach, because the voltage there is high.

Verticals have the opposite problem: the antenna is simple, but the ground system decides the efficiency. A quarter-wave vertical on the ground with only a handful of short radials can waste a large share of the power in ground loss. Many short radials (16 or more) or a few resonant elevated radials make a big difference. Short loaded verticals for 80 and 160 m are a trade-off in efficiency, no matter how good the SWR looks.

Magnetic loops attract stealth-minded operators because they're compact and quiet on receive. The trade-offs are high Q, very narrow bandwidth, retuning for every frequency change, kilovolt-level voltage across the capacitor at 100 W, and efficiency that depends heavily on conductor size and joint resistance. On the lower bands a small loop's efficiency can fall steeply.

For HOA situations, the practical tools are thin dark wire strung between trees, a flagpole-style vertical, or an attic antenna. Attic installs work but have to deal with wiring, ducts and roofing, which add loss and noise. Rules also differ. In the US, PRB-1 covers state and local government regulation, not private deed covenants, so check which one applies to you.

So, with a limited footprint, which compromise would you pick, and why? Is a single 40 m EFHW with a good choke a better starting point than a 130 ft doublet at lower height? And where would you draw the line on a loop or vertical for the lower bands?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The SWR-versus-efficiency point can't be repeated enough. I'd add that for a small lot the real question is which antenna lets you get the most wire in the air at the highest point. A 130 ft doublet at 25 ft will often be a better all-band radiator than a loaded antenna at the same height, even though the doublet needs a tuner and the other one shows a flat match.

If I were choosing for HOA stealth with a decent tree, I'd consider a doublet or an inverted V fed with ladder line. The ladder line is nearly invisible, the tuner takes care of the mismatch, and the losses stay low as long as the line is kept away from metal and routed with sensible spacing. The one thing to watch is common-mode current where the ladder line meets the tuner. Use a 4:1 current balun or a proper choke there, and don't let the feedline run in parallel with the wire for long.

The EFHW is attractive for portable and quick installs because it needs no tuner on its resonant bands. But it's resonant on the fundamental and harmonics only, so a 40 m version covers 40, 20, 15 and 10 m, and 30, 17 and 12 m need a tuner and a little patience. Pay attention to the transformer too. A small core running 100 W on SSB is fine, but 100 W of FT8 at a high duty cycle can heat a marginal core. The core mix and size matter more than the ratio printed on the box.

  • Moderators

One thing about the vertical: the radial advice depends on what you can hide. A lawn vertical with buried radials is nearly invisible, and the radials can be put down with a slit trench or just laid on the grass and left to be overgrown. If you can only manage four or so radials, make them resonant and elevate them a few feet rather than lay them on the ground. Elevated radials are less lossy per wire, and drooping them at about 45 degrees brings the feedpoint close to 50 ohms. A ground-mounted vertical with many radials is closer to 36 ohms, and the match is usually fine either way.

Verticals are good for low-angle DX and bad for local noise. If the neighborhood is noisy, a vertical will often hear more of it than a horizontal wire does, because of the polarization. That's where a small receive loop or a magnetic loop earns its place. It's a good receiver in a noisy location, even if on transmit it only makes sense on the higher bands or when a larger diameter is possible.

On the trap dipole question: traps shorten the antenna and give multiband operation without a tuner, but each trap adds some loss and narrows the bandwidth, especially on the lower band. If you have the room for a full-size wire dipole, it will usually be more efficient than a trapped one. If you don't, a trapped dipole is a legitimate compromise, and the best way to judge it is the height and the length available rather than the label.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.