Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building your first homebrew QRP rig: what to build first, and what test gear actually matters?

ci_cover.jpg

Lots of people start with a Pixie, a Tuna Tin 2 style crystal transmitter, or a BITX or uBITX board, and then hit the same wall: the thing is built, but there is no good way to know whether it is working properly. Here is a build order and a minimum set of test gear that tends to prevent most problems.

Start with the support gear, not the radio. A 50 ohm dummy load, a current-limited supply, and a basic RF power indicator are worth more than a fancy enclosure. A bench supply with a current limit lets you set 100 to 200 mA for the first power-up, so a solder bridge or a backwards electrolytic dies cheaply. If you do not have a limiting supply, a series resistor or a small fuse in the positive lead is a poor man's version. A reverse-polarity diode across the input, with a fuse ahead of it, is cheap insurance on any kit.

Then build in stages and test each stage before moving on. For a direct conversion receiver that means audio amplifier first (touch the input and listen for hum), then the product detector, then the front-end filter and VFO. For a transmitter it means oscillator first: confirm frequency with a counter or an SDR, confirm it starts reliably, and only then add the driver and final. A transmitter whose oscillator chirps or drifts is much easier to fix before the amplifier stages are wired up.

Measure output power into the dummy load, not the antenna. A diode-detector RF probe on a multimeter gets you a rough figure: peak volts, divide by 1.414 for RMS, then use P = V²/50. It is crude, but good enough to tell 0.5 W from 5 W. A scope makes it far better because you can see the waveform shape, clipping, and whether the keying envelope is clean.

Harmonics are the part many first builds skip, and it matters more than most people expect. Single-ended class C or class E finals, and the square-wave outputs of an Si5351 as used in uBITX-style designs, produce strong harmonics unless filtered. A properly built low-pass filter (a 5-pole Chebyshev or similar, with toroids wound for the right inductance) on each band is a must. If you check output with an SDR, put a proper attenuator chain in between (a 30 to 40 dB pad or more, depending on power), because a QRP transmitter can still overload or damage an SDR front end. Spurious emission limits vary by country, so check your own rules, but a good target is harmonics at least 40 dB below the carrier.

On soldering: for leaded solder, a temperature around 330 to 350 C with decent flux is plenty for kit work. Enameled toroid wire is the classic trap. Many builders get a joint that looks fine but has no electrical contact because the enamel was not fully removed. Check each winding for continuity before installing it, and ideally check inductance with an LC meter, because turn counting and spacing errors are common.

I would like to hear how others sequence projects. If someone is picking between a Pixie, a Tuna Tin 2 style crystal rig, and a BITX for a first transmitter, which would you point them toward, and what is the one test instrument you would buy before anything else?

  • Replies 2
  • Views 40
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The answer depends on what the person wants to learn. A Pixie-type transceiver is cheap and teaches a lot about how a transmitter final can double as a mixer, but it is a very rough receiver: wide, no real selectivity, and lots of out-of-band signals, so it can feel disappointing on a busy band. A crystal-controlled one-band transmitter like the Tuna Tin 2 is better for learning about oscillators, keying, matching, and output filtering, and it pairs well with a simple direct conversion receiver. A BITX is a bigger step because you are dealing with SSB generation, a crystal filter, bidirectional amplifier stages, and alignment. It is very rewarding but less forgiving without a signal source and a way to see what you are doing.

On the instrument question, I would say a frequency counter or an inexpensive SDR used as a receiver for monitoring your own oscillator, before a scope. Many first-time problems are simply that the oscillator is not where you think it is, or it is running on a harmonic or overtone of the crystal.

  • Moderators

I would add two cheap items to the list: an SWR bridge you build yourself and a simple keyer or at least a clean keying circuit. A resistive or Wheatstone-style return loss bridge is easy to build and teaches a lot. Just keep leads short, use matched resistors, and check it into the dummy load first (it should show a very good null), then into an open and a short, to confirm it responds the way it should. A tandem match or Bruene-style SWR meter is also nice for monitoring forward and reflected power, but calibrate it against something known before trusting the numbers.

For keying, a transmitter that clicks badly is annoying to everyone on the band. A simple RC network or a slightly slower keying transistor to shape the rise and fall of the envelope helps a lot, and a scope will show you the result. Also be careful that keying the oscillator itself does not cause chirp. Often it is better to leave the oscillator running and key a later stage, though that needs good shielding or layout to avoid leakage into the receiver.

Finally, if you are using a uBITX or similar, do not trust that the output is clean on every band just because it works. Check the low-pass filter board, confirm what is actually on each band, and look at the output on an attenuated SDR or spectrum analyzer before putting it on air.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.