ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
SSB audio chain: mic gain, ALC, compression, EQ and bandwidth for clean, readable signals
Most SSB audio problems come from the same few settings: too much mic gain, too much processing, or too much low-frequency energy. Here is a working order of operations, and I'd like to hear where others disagree.
Start with sideband convention. By long-standing practice, LSB is used on 160, 80 and 40 meters, and USB on 20 meters and up. On 60 meters in the US, channelized operation uses USB. VHF and UHF SSB is normally USB. Using the wrong sideband won't damage anything, but the other station will hear inverted, unintelligible audio, or will have to retune to find you. When a net or DX station uses something unusual, follow them.
Next, mic gain and ALC. On most rigs, SSB output power depends on audio level, so the mic gain control is effectively a drive control. Set it with the processor off first. Speak at normal volume and adjust gain until the ALC meter just flickers on voice peaks, and stays within the manufacturer's recommended zone. Pushing ALC deep into its range means the radio is clamping peaks, which adds distortion and widens your signal. Remember that ALC is a protection and leveling circuit, not a loudness booster. If you run an amplifier, you also have to watch the amp's own ALC or drive limits, and never drive the radio so hard that it flat-tops.
Mic technique matters more than most menu settings. A dynamic or headset mic is usually placed a couple of fingers from the lips, slightly off-axis so plosives ('p' and 'b') don't blast the diaphragm. A foam windscreen or pop filter helps. Moving closer boosts bass through proximity effect, which can sound boomy and wastes power on frequencies that add little to intelligibility. A small room with hard surfaces, a noisy fan, or an open speaker can also color the audio more than the equipment does.
Equalization and TX bandwidth should be used to subtract before you add. Many rigs let you set the transmit passband, for example roughly 100 to 2900 Hz for relaxed ragchewing, or a narrower 300 to 2700 Hz for crowded bands and DX. Rolling off below about 200 to 300 Hz often cleans up rumble and lets average power go into the speech frequencies. A mild lift in the 2 to 3 kHz region can improve presence, but heavy boosts increase sibilance and make the signal sound harsh. Make small changes and compare, rather than copying someone else's numbers, because every mic and voice is different.
The speech processor deserves restraint. Depending on the radio, it may be RF clipping, AF compression, or a combination. It raises average power, which can help in noise or on weak paths, but heavy compression raises background noise, brings up room sound, and reduces naturalness. Moderate settings are generally better than maximum. If your rig shows compression level, many operators stay in the lower range, and turn the processor off when the band is quiet and a signal is already strong. When you add processing, you usually have to reduce mic gain, because the processor works on the same signal and ALC can respond more quickly.
The monitor function is useful but easy to misread. It lets you hear your own transmitted audio, which helps you catch hum, hiss, popping and obvious distortion. Use headphones to avoid feedback. Keep in mind that monitor audio is not a perfect picture of what is happening in RF, so it may not reveal splatter or overdrive. A second receiver, an SDR, or a trusted local station giving detailed reports gives a better check. Ask specific questions: does it sound muffled, bassy, harsh or distorted, and does it get worse when the processor is on?
On receive, the usual 2.4 kHz filter is a good starting point because it balances readability and noise rejection. Narrower filters around 1.8 to 2.1 kHz can cut adjacent-channel interference and noise, at the cost of a thinner, less natural sound. Wider settings are more pleasant for strong signals and ragchews. IF shift or passband tuning is often more useful than just changing width, because it lets you move the window away from a close neighbor. Use noise reduction in small amounts, because heavy DSP can create artifacts that hide weak speech. Pay attention to AGC speed and RF gain too, since a strong nearby signal can desensitize the receiver and make a weak station seem worse than it is.
For weak stations and DX, readability usually wins over fidelity. Speak slightly slower, keep your callsign clear, use standard phonetics, and send it once or twice instead of repeating it constantly. In pileups, listen for the DX operator's pattern first. If they work split, set your transmit frequency using the second VFO or XIT, and check that you aren't sitting on the DX frequency. Use only the power needed, avoid ALC overshoot, and keep the audio clean, because a distorted signal that is slightly louder can be harder to copy than a clean one. Antenna improvements and lower local noise often yield more benefit than any processing setting.
What settings do you start with when you build a new audio profile, and how do you test them? I'm especially interested in how people decide between a narrow DX profile and a more natural ragchew profile.
Most SSB audio problems come from the same few settings: too much mic gain, too much processing, or too much low-frequency energy. Here is a working order of operations, and I'd like to hear where others disagree.
Start with sideband convention. By long-standing practice, LSB is used on 160, 80 and 40 meters, and USB on 20 meters and up. On 60 meters in the US, channelized operation uses USB. VHF and UHF SSB is normally USB. Using the wrong sideband won't damage anything, but the other station will hear inverted, unintelligible audio, or will have to retune to find you. When a net or DX station uses something unusual, follow them.
Next, mic gain and ALC. On most rigs, SSB output power depends on audio level, so the mic gain control is effectively a drive control. Set it with the processor off first. Speak at normal volume and adjust gain until the ALC meter just flickers on voice peaks, and stays within the manufacturer's recommended zone. Pushing ALC deep into its range means the radio is clamping peaks, which adds distortion and widens your signal. Remember that ALC is a protection and leveling circuit, not a loudness booster. If you run an amplifier, you also have to watch the amp's own ALC or drive limits, and never drive the radio so hard that it flat-tops.
Mic technique matters more than most menu settings. A dynamic or headset mic is usually placed a couple of fingers from the lips, slightly off-axis so plosives ('p' and 'b') don't blast the diaphragm. A foam windscreen or pop filter helps. Moving closer boosts bass through proximity effect, which can sound boomy and wastes power on frequencies that add little to intelligibility. A small room with hard surfaces, a noisy fan, or an open speaker can also color the audio more than the equipment does.
Equalization and TX bandwidth should be used to subtract before you add. Many rigs let you set the transmit passband, for example roughly 100 to 2900 Hz for relaxed ragchewing, or a narrower 300 to 2700 Hz for crowded bands and DX. Rolling off below about 200 to 300 Hz often cleans up rumble and lets average power go into the speech frequencies. A mild lift in the 2 to 3 kHz region can improve presence, but heavy boosts increase sibilance and make the signal sound harsh. Make small changes and compare, rather than copying someone else's numbers, because every mic and voice is different.
The speech processor deserves restraint. Depending on the radio, it may be RF clipping, AF compression, or a combination. It raises average power, which can help in noise or on weak paths, but heavy compression raises background noise, brings up room sound, and reduces naturalness. Moderate settings are generally better than maximum. If your rig shows compression level, many operators stay in the lower range, and turn the processor off when the band is quiet and a signal is already strong. When you add processing, you usually have to reduce mic gain, because the processor works on the same signal and ALC can respond more quickly.
The monitor function is useful but easy to misread. It lets you hear your own transmitted audio, which helps you catch hum, hiss, popping and obvious distortion. Use headphones to avoid feedback. Keep in mind that monitor audio is not a perfect picture of what is happening in RF, so it may not reveal splatter or overdrive. A second receiver, an SDR, or a trusted local station giving detailed reports gives a better check. Ask specific questions: does it sound muffled, bassy, harsh or distorted, and does it get worse when the processor is on?
On receive, the usual 2.4 kHz filter is a good starting point because it balances readability and noise rejection. Narrower filters around 1.8 to 2.1 kHz can cut adjacent-channel interference and noise, at the cost of a thinner, less natural sound. Wider settings are more pleasant for strong signals and ragchews. IF shift or passband tuning is often more useful than just changing width, because it lets you move the window away from a close neighbor. Use noise reduction in small amounts, because heavy DSP can create artifacts that hide weak speech. Pay attention to AGC speed and RF gain too, since a strong nearby signal can desensitize the receiver and make a weak station seem worse than it is.
For weak stations and DX, readability usually wins over fidelity. Speak slightly slower, keep your callsign clear, use standard phonetics, and send it once or twice instead of repeating it constantly. In pileups, listen for the DX operator's pattern first. If they work split, set your transmit frequency using the second VFO or XIT, and check that you aren't sitting on the DX frequency. Use only the power needed, avoid ALC overshoot, and keep the audio clean, because a distorted signal that is slightly louder can be harder to copy than a clean one. Antenna improvements and lower local noise often yield more benefit than any processing setting.
What settings do you start with when you build a new audio profile, and how do you test them? I'm especially interested in how people decide between a narrow DX profile and a more natural ragchew profile.
Link to comment
https://www.hamradiobase.com/forums/topic/10846-ssb-audio-chain-mic-gain-alc-compression-eq-and-bandwidth-for-clean-readable-signals/Share on other sites