Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Band plan vs. FCC rules: how do you decide where to operate and how close to the band edge is safe?

ci_cover.jpg

Question for the group, since this trips up a lot of newly upgraded operators: what is the practical difference between the FCC rules and the ARRL band plan, and how do you pick a frequency on 160 through 10 meters, plus 6 m, 2 m, 70 cm and 33 cm?

Some specifics I'd like to see covered. Where do CW, digital and phone usually sit on each HF band? How far inside a privilege edge should the dial be set for SSB? What is different about 60 meters? And when you talk to people in other countries, how much do the allocations change? Please correct me if I've mixed anything up, and treat the answers as a starting point to check against the current rules.

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the distinction: Part 97 is the law, and the ARRL band plan is a voluntary agreement on how to share the space. The FCC defines which license classes may use which segments, the permitted emission types, and the power limits. The band plan tells you where operators conventionally put CW, digital, SSB, beacons, and so on. You can be fully legal and still be parked on top of an FT8 cluster or a net.

On privileges, the broad strokes for US licenses are these. Technicians have limited HF: CW on parts of 80, 40 and 15 meters, CW and data on 10 meters from 28.000 to 28.300, and SSB on 28.300 to 28.500, with a 200 W PEP limit. Technicians also have all amateur privileges above 50 MHz. Generals get most of every HF band but not the lower slices reserved for Extras. For example, General phone on 80 m starts at 3.800 where Extra starts at 3.600, on 40 m at 7.175 versus 7.125, on 20 m at 14.225 versus 14.150, and on 15 m at 21.275 versus 21.200. Extras have everything. Check the current FCC chart for exact segments, because it's easy to misremember one edge.

For the band edge itself, remember that the dial frequency is not where your signal ends. With suppressed-carrier SSB, a USB signal extends about 2.7 to 3 kHz above the dial and an LSB signal about the same amount below it. So at the bottom of an LSB phone segment, set the dial a few kHz inside the edge, not right on it. At the top of a USB segment, do the same in the other direction. The same goes for digital modes: the whole signal's bandwidth has to fit inside the segment, not just the dial frequency.

Common digital spots are worth knowing, since the modes cluster there. FT8 is generally found around 1.840 on 160, 3.573 on 80, 7.074 on 40, 10.136 on 30, 14.074 on 20, 18.100 on 17, 21.074 on 15, 24.915 on 12, 28.074 on 10 and 50.313 on 6 m. These are dial frequencies in USB mode, and activity patterns can shift, so confirm in your logging or decoding software before you rely on them. The QRP CW calling frequencies are also widely known, such as 7.030 and 14.060.

For 60 meters, the US doesn't have a continuous band. It uses five channels, and General and Extra licensees may use them under an ERP limit relative to a half-wave dipole, with a narrow bandwidth. The channel centers are 5332, 5348, 5358.5, 5373 and 5405 kHz. For USB the dial is set 1.5 kHz below center, so 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5. Don't just tune a nearby frequency, because the channelization is what makes it legal. Verify against the current rules before transmitting, as the 60 m rules have changed over the years.

  • Moderators

Adding the VHF/UHF side and the international piece, which is where simple band charts stop being enough.

On 6 meters, the bottom of the band is for weak-signal work. CW and beacons sit near the low end, and SSB activity is centered on the 50.125 calling frequency. FT8 is at 50.313. FM and repeaters live higher up, and 52.525 is the national FM simplex calling frequency. On 2 meters, 146.520 is the national FM simplex calling frequency, 144.200 is the SSB/CW weak-signal calling frequency, and 144.174 is the usual FT8 spot. The simplex portions of the FM section run roughly 146.40 to 146.58 and 147.42 to 147.57, with repeater pairs filling much of the rest. On 70 cm, 446.000 is the national simplex calling frequency and 432.100 is the usual weak-signal calling frequency. Local band plans differ because repeater coordinators set local pairs and offsets, so look up your regional plan before programming a radio.

On 33 cm (902 to 928 MHz), expect a different environment. It's a shared band with other services and unlicensed devices, and the amateur service is not the only occupant. It's also not available in many other countries, so don't assume a rig with 33 cm will have contacts everywhere. 902.100 is commonly cited as a weak-signal calling frequency, but the band is lightly used in many areas. Local coordination matters a great deal. Also note that parts of 70 cm have location-based restrictions near some government radar installations and border areas, so read the Part 97 notes if you operate close to those.

For international allocations, the world is divided into IARU regions. Region 1 covers Europe, Africa and the Middle East, Region 2 covers the Americas, and Region 3 covers Asia and the Pacific. The band edges differ by region. For example, 80 m is 3.5 to 3.8 MHz in much of Region 1 versus 3.5 to 4.0 in the US, 40 m is 7.0 to 7.2 in Regions 1 and 3 versus 7.0 to 7.3 in Region 2, and 2 m is 144 to 146 in Region 1 versus 144 to 148 in the US. That matters for split operation on DX contacts. Overseas stations may be transmitting on frequencies you can't answer on, or the reverse, so know your own limits.

If you operate from another country, you follow the host country's rules and allocations, not your home privileges. Reciprocal arrangements such as CEPT recommendations or the US IARP exist, but you still have to check the actual band and power limits for the country. Also remember that 30, 17 and 12 meters (the WARC bands) are not for contest operation under the contest rules and conventions, and that 60 m allocations are narrow and vary a lot by country.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.