Breaking the pileup on a rare one: split, timing, and how to prepare for Clipperton or Bouvet-class targets
- Replies 2
- Views 36
- Created
- Last Reply
Top Posters In This Topic
-
Admin_Terry 1 post
-
Mod_Chrissy 1 post
Most pileup advice boils down to "just call more." In practice the stations that log a rare entity quickly tend to do a few specific things right. Here is how I'd break it down, and I'd like to hear where others disagree.
Work out the operating pattern before you transmit. Listen for at least several minutes. Is the DX working split? Is he listening up 1, up 2 or up 5? Is he working by call area, by continent, or by the last letters of the call? A good operator will announce the pattern, but you still have to hear it. Put the DX on VFO A to receive, put your transmit on VFO B in the listening window, and confirm in a dummy load or by monitoring that you are actually transmitting where you think you are. Many people call on the DX's own frequency by mistake because they forgot to enable split. Also check your band edges and mode sub-bands. A wide split near a band limit can put you out of the allocation.
Find a spot in the pile. Listening up 3 to 5 kHz means a large block of callers, and the pileup has structure. Some stations zero-beat the last station worked. Others use a fixed offset. If the DX is walking up the band, the best frequency is often the one just ahead of where he is currently listening, not the middle of the crowd. Use RIT or XIT sparingly and watch how far you've drifted. Repeatedly shifting to a clean-looking frequency often just moves you into the next group of callers.
Timing matters more than power. Transmit when the DX has just finished a QSO, not while he is working someone else. Calling over the end of an exchange is what most people call tailending. In a fast pile it can be hard to tell the difference between calling right after the last 73 and stepping on it. The cleaner approach is to start your call when the previous QSO has actually ended, using the DX's rhythm as your cue. On CW that means sending your call once or twice at a clear speed, not repeating it twenty times. On SSB, give your call once with standard ITU phonetics, then listen. If he returns a partial, repeat only your callsign, not a speech.
Don't send extras. "Please," "DX," your name and your location slow everyone down. If he returns "JA1 only" and you're not in JA1, wait. If he asks for a particular call area, calling anyway is the quickest way to get yourself reported in the cluster comments.
Use spots, but verify. A cluster spot or RBN skimmer spot tells you the DX is probably active, but not that it is the right callsign, and busted spots happen. Hear the station yourself before you believe the spot. If you are going to spot something, put the exact frequency in the comment and add something like "UP 2" if split. If you are using skimmer data to check propagation, remember that it shows who could hear whom, not that you will be able to work him.
Low bands change the game. On 160 and 80 meters, listening matters as much as transmitting. You cannot work what you can't hear, so a good receive antenna (a Beverage, a loop or a small receiving array, depending on your space) often helps more than extra transmit power. Grey-line timing and a quiet geomagnetic field help considerably. The DX often hears you at a very low level, so send clearly and don't change your timing unpredictably.
FT8 and the Fox/Hound mode. If the DXpedition uses WSJT-X's DXpedition mode, set yourself up as a Hound. Call above the Fox's frequency range, stay in your own slot, and don't keep transmitting after you've received your report. Calling on the Fox's own frequency can destroy the multi-stream setup he's using.
Targets like Clipperton and Bouvet. Clipperton (FO) and Bouvet (3Y) are logistically very difficult places, and those are the kinds of entities that bring huge pileups when they are active. The expedition planning (permits, shipping, landing conditions, power, antennas near salt water, several stations with filters to avoid interference) is serious work and often shapes what the on-air plan looks like. As a chaser, check the expedition's published operating plan, and read whatever they say about log updates, QSL routes and band priorities. Club Log's Most Wanted list and its log search tools are useful here: you can see whether you're in the log and decide whether you need another band or mode, rather than making duplicate calls.
Questions for the thread: how do you decide between calling on the DX's exact listening pattern and trying a different spot in the pile? And for the low bands, what is your actual receive setup, and has it changed the way you decide when to call?
Link to comment
https://www.hamradiobase.com/forums/topic/10861-breaking-the-pileup-on-a-rare-one-split-timing-and-how-to-prepare-for-clipperton-or-bouvet-class-targets/Share on other sites