Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a field comms station: power layout, noise control, antennas and checklists for EMCOMM deployments

ci_cover.jpg

I want to work through a baseline field station layout for EMCOMM-style deployments and see where people would change it. The scenario is a two-position station (HF plus VHF/UHF) under a pop-up shelter, running for 8 to 12 hours, with a generator available but not assumed. Most failures in this kind of setup come from the interfaces: power to radio, radio to feedline, feedline to antenna, and generator to everything else. The radios themselves rarely cause the trouble.

Start with the power budget, because it decides everything downstream. Battery energy is volts times amp-hours, so a 100 Ah LiFePO4 battery at a nominal 12.8 V holds about 1,280 Wh. Treat 80 to 90 percent of that as usable, depending on the BMS and how low you are willing to run. A typical 100 W HF rig draws roughly 1 to 3 A receiving and 20 A or more at full output on key-down modes. Voice and digital duty cycles differ a lot, so average the load by mode instead of using the peak figure. Add a VHF/UHF mobile, a laptop, lighting, a charger or two, and any router or Wi-Fi gear, then write the total down in watt-hours per hour. If the number says the battery lasts 14 hours, plan on 8 to 10 and keep a recharge path ready.

For distribution, my starting point is a single fused feed from the battery. Put the fuse or breaker as close to the positive terminal as practical. Run it to a Powerpole-based distribution block with individual fusing per branch, and size wire for both ampacity and voltage drop. Voltage drop matters more than people expect, because a long, thin run can leave an HF rig sagging into low-voltage alarms or distorted transmit audio on peaks. Pick one polarity orientation for the whole group and label it so nobody has to guess when borrowed gear shows up.

For the RF side, the usual baseline is a resonant wire antenna on a mast for HF, with a 1:1 current choke at the feedpoint and another at the radio. For regional work on 80 or 40 m, a low horizontal dipole or inverted-V gives you NVIS-style coverage. A simple vertical on 20 m or higher is better when you need distance. VHF/UHF goes on a separate mast or a short pole with the shortest practical low-loss coax, since feedline loss matters far more at 146 and 446 MHz than at HF.

The open questions I would like input on: how are you keeping generator and solar noise out of receive, what grounding do you actually do in the field, and what is on your setup and teardown checklists that you would not want to skip?

  • Replies 2
  • Views 48
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On noise, the biggest lever is distance and sequencing. Get the generator placed first, downwind of the shelter and well away from the operating position, both for carbon monoxide and for RFI. A CO alarm in the tent is cheap insurance even when the generator is far away, because wind shifts. Keep fuel storage separate, and let the engine cool before refueling.

Inverter generators are cleaner than old conventional ones in terms of waveform, but the inverter and engine ignition can still radiate on HF. Test before you commit: tune to a quiet frequency on 80, 40 and 20 m with the generator off, then on, and compare the S-meter and the noise floor. Try with and without eco throttle, since the changing engine speed can turn a steady hiss into something that hunts up and down. If the AC output cord is radiating, ferrite chokes on the cord near the generator, and sometimes near the charger, can help. Use a ground-fault protected outlet for anything outdoors, and follow the manufacturer's guidance on grounding and neutral bonding rather than improvising with a rod and a jumper.

Solar is quiet in the sense that panels do not make noise, but the controllers can. Some inexpensive MPPT units put out a lot of broadband hash on HF. Use a controller with a proper LiFePO4 charge profile, keep it and its wiring away from the antenna and receive gear, and check noise with it connected and disconnected. If a controller is a problem, move it, add chokes on both the panel and battery leads, or run the panels disconnected from the station while you operate.

One last LiFePO4 point: check the cold-weather charging limits on your battery. Many BMS designs will not accept charge below freezing unless the battery has built-in heating, and a solar plan that ignores this can leave you with a battery that quietly stops charging.

  • Administrators

On antennas and grounding, I would add a few cautions. Masts and guy lines are where people get hurt or cause damage. Survey the site for overhead power lines before anything goes up, and make sure that if the mast fell in any direction it could not reach a conductor. Guy a telescoping mast at several points, typically three at roughly 120 degrees, with stakes set deep enough for the soil and flagging on every line so people do not trip. A fiberglass mast is not a guarantee of safety if there is wire running up it, and wet or windy conditions change the picture fast. Have a wind limit in mind and take the antenna down before you reach it, not after.

Grounding in the field is mostly about static discharge, bonding the equipment together, and sometimes noise. It is not lightning protection. A short ground rod will not make a station safe in a thunderstorm. If lightning is a real possibility, the plan is to disconnect feedlines and shut down, then retreat to proper shelter. Bonding the station chassis, the power distribution and the coax shield entry point together is useful. Dissipating static from the coax by touching the shield to the ground point before you connect it to the radio is a good habit. Whether a rod improves receive noise varies by setup, so test it rather than assuming.

For coax, use the shortest run that gets the antenna clear of the shelter and people, add drip loops at the entry point, and secure the cable so tent movement does not yank connectors. At HF, RG-58-class cable is usually acceptable for short runs. At VHF/UHF the difference between thin coax and something like LMR-400 class cable can be several dB over a 100 ft run, so use better cable or shorten the run.

For checklists, I would split them into site, power, RF, and operations. Setup order: survey hazards, place the generator, set up the shelter, raise masts, run feedlines, connect power and fuses, then power up the radios and test each one on a dummy load or low power before going on air. Teardown is the reverse, plus a count of stakes, adapters, chokes and fuses, a fuel check, and a walk of the site for anything left behind. Add the served agency's logging and message forms to the operations list so they are not rediscovered halfway through the day.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.