Building solid CW copy and sending: keyers, paddles, filters, Farnsworth and where decoders fit
- Replies 2
- Views 46
- Created
- Last Reply
Top Posters In This Topic
-
Admin_Terry 1 post
-
Admin_Lee 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
This thread is for comparing practical approaches to CW operating, from the key at your fingertips to what comes out of the speaker. Many of the same questions keep coming up: which paddle or keyer settings to use, how narrow to set the filter, when to use QSK, and how much to rely on software decoders. Here are some starting points for discussion.
Timing basics. Everything in Morse is built on one unit. A dit is 1 unit, a dah is 3, the gap inside a character is 1, the gap between characters is 3, and the gap between words is 7. Speed is usually measured with the word PARIS, which is 50 units. A dit length in milliseconds is therefore about 1200 divided by the WPM. At 20 WPM that is 60 ms. Sloppy sending is usually a spacing problem rather than a speed problem, so listen to your own gaps as much as your elements.
Farnsworth and Koch. Farnsworth timing sends each character at a faster speed, for example 18 to 20 WPM, and stretches the spacing between characters and words to bring the overall speed down. The aim is to hear each character as a single sound rather than counting dits and dahs. It pairs well with the Koch method, which starts with full-speed characters and only a couple of letters, then adds more as you reach good accuracy. A common mistake is to shrink the extra spacing too slowly or never at all. Once copy is comfortable, bring the gaps down toward standard timing.
Keys and keyers. A straight key gives you full control of timing and is fine for learning rhythm. Paddles with an iambic keyer let you squeeze both levers to alternate dits and dahs. Mode A and Mode B differ in what happens when you release the squeeze. Mode B adds one extra opposite element if you release during an element, and Mode A does not. Neither is the correct one, and you should pick whichever makes your sending cleanest. A bug (such as the Vibroplex designs) makes dits automatically with a pendulum and leaves dahs manual, so it has its own distinctive swing. Whatever you use, the adjustments that matter most are contact gap, spring tension and weight. Paddles from makers such as N3ZN, Begali and Vibroplex are often compared on exactly that feel.
Filters and QSK. A CW filter in the 300 to 500 Hz range is a common starting point. Very narrow filters can ring and make weak signals sound smeared, and they also hide the activity around you. Matching the sidetone to your receive pitch helps you zero-beat and stay on frequency. QSK, or full break-in, lets you hear the band between elements so you can tell if someone has started calling. It needs fast, quiet transmit-receive switching, and not every amplifier relay will keep up. Semi break-in with a short hang time is a reasonable compromise.
Abbreviations and prosigns. Standard shorthand includes CQ, DE, K, KN, TU, 73, UR, RST, QRS, QRQ, QRM, QRN and QSB. Prosigns are sent as one character with no gap: AR (.-.-.) ends a transmission, SK (...-.-) ends a contact, BT or = (-...-) is a break or pause, KN (-.--.) invites only the named station, and AS (.-...) means wait. Overusing abbreviations on a casual QSO can confuse newer operators, so plain language usually works better.
Skimmers and decoders. CW Skimmer and the Reverse Beacon Network are good for seeing who is on the band and how well your signal is heard. Decoders do well on clean, steady machine-sent code. They tend to struggle with fading, noise, interference and uneven hand sending. Use them as an aid, not a substitute for learning to copy by ear. In contests, check whether your category allows spotting or decoding assistance.
Contests. CW contests reward clean, repeatable exchanges and a steady rhythm. Common cut numbers include 5NN for 599, and T and N for zero and nine in some exchanges. Stay at a speed you can copy reliably and use a message keyer for CQs and repeats. Send the call sign at a pace that gets it copied the first time.
So which parts are giving you trouble: keyer mode, filter width, going from slow to faster copy, or contest exchanges? Post your setup and what you would like to improve.
Link to comment
https://www.hamradiobase.com/forums/topic/10866-building-solid-cw-copy-and-sending-keyers-paddles-filters-farnsworth-and-where-decoders-fit/Share on other sites