Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Gain, overload and noise floor in budget SDRs: how to tell what your dongle, antenna and software are really doing

ci_cover.jpg

A lot of SDR troubleshooting comes down to one question: is the weak-signal performance limited by the antenna and local noise, or by the receiver's front end and ADC? The answer changes depending on whether you use an RTL-SDR dongle, an Airspy, an SDRplay RSP, a HackRF or a LimeSDR. It also changes with the band, and with whether you use SDR#, SDRuno, GQRX, HDSDR or CubicSDR as the front end.

Here are some points to compare notes on. First, the 8-bit RTL-SDR has very limited headroom. A strong FM broadcast signal can create images and intermodulation products far from the signal that causes them, and a wideband antenna makes this worse. The HackRF One is also 8-bit, and its strengths are tuning range (1 MHz to 6 GHz), sample rate and transmit capability, not sensitive reception. Radios with more effective bits, such as the SDRplay RSP family or the Airspy models, tolerate a mixed signal environment better. Even so, they are not immune to overload, and each has its own gain structure.

Second, gain is not a 'more is better' control. A practical test is to watch the noise floor with the antenna connected and again with a 50-ohm load on the input. If the antenna raises the floor by a few dB or more, the receiver is no longer the limiting factor and extra gain mostly eats headroom. If strong signals produce ghost carriers that move when you change gain, back the gain off or add a band-stop filter, such as an FM notch, before the receiver.

Third, HF needs separate treatment. Direct sampling on some RTL-SDR dongles works but is crude. An upconverter shifts HF into the dongle's normal tuning range, so you must set the LO offset correctly in the software, and you should watch for LO leakage and spurs. A dedicated HF-capable SDR is often a cleaner answer. Whatever the receiver, local noise from switch-mode supplies, USB 3 ports and LED lighting can swamp a good front end. Ferrite chokes on USB and coax, and moving the antenna away from the shack, often help more than new hardware.

What are your preferred methods for setting gain, and which software controls (AGC, FFT window and size, DC offset correction, PPM calibration) do you check first when a signal looks wrong?

  • Replies 2
  • Views 39
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One check that is easy to skip is the sample rate versus FFT resolution. Resolution bandwidth is roughly sample rate divided by FFT size, so a 2.4 MS/s capture with a small FFT can hide narrow carriers and make the noise floor look higher than it is. Raising the FFT size or narrowing the span usually gives a more honest picture before you touch the gain. Also remember that the spike at the center of an RTL-SDR display is a DC artifact of the architecture, not a real signal. Offset tuning or an offset in the software avoids mistaking it for a carrier.

For decoding, the usual chain is receiver software, a virtual audio cable, then the decoder, for example WSJT-X or fldigi. Set the receiver to USB for most HF digital modes. Keep the audio level moderate so the decoder is not clipped, and make sure the PC clock is accurate for time-synchronized modes like FT8. If decoding fails on a clean signal, check audio sample rates on both ends and the PPM correction, which matters most at VHF and UHF where a small ppm error becomes a large frequency error.

  • Moderators

On antennas, the best choice depends heavily on band. For VHF and UHF listening, a discone or a simple ground-plane cut for the band of interest is a reasonable start. Remember a wideband antenna passes everything, including strong broadcast and paging signals, so filtering matters more. For 1090 MHz ADS-B, a tuned antenna and short, low-loss coax usually matter more than the dongle. If an LNA is used, putting it at the antenna end overcomes feedline loss, but it also reduces the headroom for strong signals, so it can be counterproductive in a crowded environment.

At HF, external noise usually dominates, so a very low receiver noise figure is often not the bottleneck. A small magnetic loop, an active loop or a random wire with a matching transformer can all work, and the deciding factor is often how quiet the location is. A common-mode choke at the feedpoint and another near the receiver is cheap and often reduces noise pickup on the coax.

A panadapter setup is a separate case. It taps the transceiver's IF, so a buffered, high-impedance tap is important to avoid loading the radio. In software, CAT control (for example via OmniRig in HDSDR) keeps the display frequency in step with the rig. Check the manual for your rig's IF frequency before wiring anything.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.