Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Gain, overload and ghost signals: getting real dynamic range from RTL-SDR, SDRplay, Airspy and HackRF

ci_cover.jpg

A common complaint with wideband SDRs goes like this: the waterfall looks crowded the moment a decent antenna is connected, the noise floor jumps, and signals appear in places where nothing should be. People often blame the software, but SDR#, SDRuno, GQRX, HDSDR and CubicSDR all display the same samples. Most of the time the cause is the front end running out of dynamic range, or local noise getting in through the antenna and the USB cable.

Here is a framework for discussion. Sensitivity and dynamic range are different things. A dongle can hear a very weak signal on a quiet band and still fall apart when a strong broadcast transmitter sits a few megahertz away. Dynamic range is limited by the ADC resolution, the analog front end (LNA, mixer, filtering) and how you set the gain. Roughly, each ADC bit adds about 6 dB of theoretical range. That is why an 8-bit device such as the RTL-SDR (RTL2832U) or HackRF One has much less headroom than a 12-bit Airspy R2 or a 14-bit SDRplay RSP-series receiver. Real performance also depends on the tuner and filters, so the bit count is only a rough guide.

The simplest test for overload is to change the gain and watch the signals. Reduce the RF or LNA gain by 10 dB. A real signal should drop by about 10 dB, and the noise floor should move with it. Third-order intermodulation products fall about 3 dB for every 1 dB of reduction in the offending signals, so they vanish much faster than real signals. If a "signal" appears or disappears out of proportion to the gain change, or mirrors a strong signal on the opposite side of the tuned frequency, suspect intermod or an image. An FM broadcast notch or a bandpass filter ahead of the dongle will often clean things up more than any software setting.

HF needs its own discussion. The RTL-SDR can do direct sampling on some models, such as the RTL-SDR Blog V3, which is simple but limited by 8-bit quantization and weak filtering. Without good preselection, strong broadcast stations overload the ADC quickly. An upconverter shifts HF into the range the tuner handles well. Its LO accuracy, filtering and spurs all matter, and you have to apply the correct offset in the software, otherwise every frequency readout is wrong by the LO value. Purpose-built HF receivers like the Airspy HF+ family or SDRplay units with HF input and notch filters generally cope better with crowded bands than a dongle with a converter.

Antenna and noise questions matter just as much. A broadband whip or discone attached to a dongle sees everything from local FM to pagers, and that can saturate the front end. An active loop or a tuned antenna for the band you care about brings its own filtering. Common-mode noise from the USB cable, switching power supplies, LED lighting and the PC itself can raise the floor by many dB. Ferrite chokes on the coax and USB cable, a short USB extension to move the dongle away from the computer, a powered hub, and a feedline run away from household wiring are all worth trying one at a time while watching the noise floor.

For discussion: how do you set up gain staging on your own receiver? Do you start with AGC and then switch to manual, or start low and raise the gain until the noise floor just lifts? Which filters (FM notch, bandpass, LPF for HF) have made the biggest difference, and for decoding modes like FT8, ADS-B or weather satellites, have you found a gain setting where decode rates drop at both ends?

  • Replies 2
  • Views 63
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd start manual and keep AGC for casual listening. For decoding, a stable level matters more than chasing the last dB of sensitivity. With an 8-bit RTL-SDR the useful gain range is narrow, and the best setting is usually the point where the noise floor rises by a few dB when the antenna is connected, compared with a terminated input. If connecting the antenna raises the floor by 10 dB or more on a quiet band, you're probably seeing external noise or overload, and extra gain won't help.

For decoders, a rough check is to compare decode counts or SNR figures at a few gain settings. WSJT-X for FT8 shows the audio level and the reported SNR. ADS-B with dump1090 shows message counts, and for 1090 MHz a dedicated filter plus a good antenna usually beats cranking the LNA. Both ends fail. Too little gain hides weak signals, and too much creates overload artifacts that decoders handle badly.

On the software side, check the sample rate before blaming the hardware. Dropped samples from a marginal USB port or cable look like noise bursts in the waterfall and can wreck a decode. Stay at a rate your USB controller handles cleanly, and use the decimation or bandwidth controls so you don't process more spectrum than you need.

  • Moderators

Filtering gets overlooked in these threads. Broadcast FM is the usual culprit on VHF and UHF, and a notch costs very little compared with how much it helps. Several SDRplay models include switchable notches for broadcast bands, and standalone FM notch filters exist for dongles. On HF, a set of switchable bandpass filters or a tuned antenna such as a small magnetic loop makes a bigger difference than most software tweaks, because it keeps the strong out-of-band signals from ever reaching the ADC.

On the HF-with-upconverter question: it works well if you account for the offset and check that the converter's LO and spurs are clean. Calibrate with a known signal, such as a time station or a broadcaster on a precisely known frequency, and apply a ppm correction if the software offers it. SDR#, SDRuno and HDSDR can all handle an LO offset, though the setting is in different places in each. If you also use the SDR as a panadapter or bandscope next to a transceiver, tapping the IF of the radio is cleaner than a shared antenna splitter. A splitter costs signal level, and you risk damaging the SDR if you ever transmit. Only connect an SDR to a transmitting antenna path through proper protection, and check the radio's documentation for a receive-only output.

One more tip for finding noise sources: use the waterfall as a tool. Switch off breakers, unplug chargers and LED drivers one at a time and watch the floor. Birdies at regular intervals across the band often point to a specific switching supply, and moving the antenna just a few meters away can be enough to fix it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.