Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Rig dead or misbehaving? A practical triage order for no TX, no RX, SWR faults, noise and blown finals

ci_cover.jpg

Most bench time is lost by diving into the RF section before the basics are proven. Here is a triage order that works for most transceivers, with the reasoning behind each step. Please add to it or argue with it, especially on the order.

1. Prove power at the radio, under load. Check the fuse, polarity and connectors, then measure voltage at the rig's DC input while it transmits, not just at the supply terminals. A supply that reads 13.8 V at idle can sag to 11 V on transmit through a corroded fuse holder, a thin cable or a tired connector. That can cause low output, resets, distorted audio or a low-voltage shutdown that looks like a dead transmitter.

2. Split the problem: receive, transmit, or both. If both are dead, suspect common paths: power rails, the reference oscillator, PLL lock, the CPU or display, the antenna relay or the antenna connector. If only one is dead, work along that chain.

3. No receive. Start with the simple items: squelch, AF gain, RF gain, attenuator, preamp setting, and the speaker or headphone jack switching contacts. Then check whether the noise floor changes when you touch the antenna input. If it does not, trace the signal with a signal generator or RF probe from the antenna jack through the T/R relay, band filters, mixer, IF filters and detector. Also confirm the local oscillator is present and locked. A PLL unlock indication or a control voltage stuck at a rail is a strong clue.

4. No transmit. Always use a dummy load and a wattmeter, never an antenna, for these tests. Confirm that PTT is actually reaching the radio and that you hear the T/R relay click. Then confirm there is drive, bias and power-control voltage on the driver and final stages. If output is low, check whether the rig is folding back because of a protection circuit before you assume the PA is bad.

5. SWR protection faults. If the rig reports high SWR or folds back on a good dummy load, the protection circuit may be reading wrongly. The usual causes are a bad detector diode, a damaged bridge transformer or toroid, a drifted trimmer, a cracked solder joint, a dirty filter relay or a damaged internal coax jumper. Do not bypass the protection to make the symptom go away. It is there to protect the finals, and a faulty reading is itself a fault to fix.

6. Noise. First decide whether it is internal or external. Disconnect the antenna and terminate the input with a dummy load. If the noise remains, it is inside the rig or coming in on the power or accessory leads. Try a clean linear supply or a battery for comparison, and check DC-DC converters, failing electrolytics, ground connections and ferrites on the leads. If the noise only appears with the antenna connected, look outside: switch-mode supplies, chargers, LED lighting and so on.

7. Blown finals. The replacement is only half the job, because finals rarely fail without a cause. Common causes include high SWR with weak protection, overdrive, a failed bias circuit, supply overvoltage, parasitic oscillation, a failed temperature sensor or bypass capacitors, and a faulty low-pass filter or output relay. Before powering up with new devices, check the bias network, gate or base resistors and driver stage. Use a current-limited bench supply, set the idle current exactly as the service manual specifies, and use the correct part or a properly matched equivalent.

8. Capacitors and contacts. Electrolytics in older rigs are good suspects for hum, noise, weak audio and supply problems. Replace them with the right voltage rating and with low-ESR types where the circuit needs them. Inspect nearby traces on surface-mount boards for electrolyte corrosion. Do not swap RF-critical capacitors for random types; match the dielectric and tolerance, because C0G/NP0 parts are often specified for a reason. For scratchy pots, switches and intermittent connectors, use a contact cleaner that is suitable for the part, and clean relay contacts only according to what the part allows.

9. Alignment last, not first. Alignment will not fix a dead stage. Once the rig works, follow the service manual's procedure for reference frequency, PLL, filters, carrier oscillator, S-meter and power output, using the specified signal source, counter and power meter. Mark the original position of any slug or trimmer before moving it.

What do you check first when the symptoms are vague, and where do you think this order should change?

  • Replies 2
  • Views 38
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd move the dummy-load step even earlier, and I'd treat the bench supply as a diagnostic instrument, not just a power source. Its current meter tells you a lot before you pick up a probe. Idle current well above the manual's figure points at a failed regulator, a shorted bypass capacitor or a PA drawing current with no drive. Current that rises smoothly when you key the radio but gives no output suggests a path problem after the PA, such as the low-pass filter, relay or output connector.

On meters, a DMM is great for DC voltages, diode checks and continuity, but be careful in RF areas. A multimeter on an RF node can read nonsense or even upset the circuit. An RF probe or an oscilloscope will show you what is actually there. For MOSFETs and transistors, the diode-test mode can reveal dead shorts, but in-circuit readings are easily misled by parallel components, so lift a lead before you condemn a part.

For a scope, 10x probes and short ground leads matter at RF. A long clip lead will distort what you see and may even change the circuit's behavior. Also take care if the equipment under test has a live chassis; use an isolation transformer where that applies.

  • Moderators

One thing I'd add to the SWR section: separate a real mismatch from a false reading by testing with a known-good dummy load and an external wattmeter. If the external meter shows sensible forward power and almost no reflected power but the rig still complains, the problem is the rig's sensing circuit, not the load. If the external meter agrees with the rig, then look at filter relays, the antenna switch and the connector or jumper between the PA and the antenna socket. High reflected power can also come from a damaged low-pass filter, not only from the antenna.

For noise, a little method helps. Note which bands it affects, whether it changes with supply voltage or the volume setting, and whether it follows the display or the backlight. A fixed spacing of birdies often points to a switching regulator or clock harmonic, while a rough buzz that moves with load suggests supply filtering. An SDR or a spectrum analyzer shows those patterns better than listening, but even a handheld AM radio held near the board can help you find the source.

With electrolytics, an ESR meter beats a capacitance reading, because a part can measure close to its marked value and still be too high in ESR for a switching supply. And before you reflow a suspect joint, check whether the board has a hairline crack nearby. Reheating one joint can hide a mechanical fault for a while without fixing it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.