Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

VHF/UHF antenna choices: J-pole vs collinear vs 5/8 whip, and why coax and connectors often matter more than the antenna

ci_cover.jpg

Here is a common 2 m / 70 cm question: you want a decent vertical antenna for FM repeaters and simplex, you might want to try a satellite pass later, and you have to pick between a J-pole or Slim Jim, a collinear, a mobile whip on a mag mount or NMO, and maybe a small yagi. The numbers in catalogs make it look like you can just buy the most dBi. In practice, pattern, polarization, feedline loss, and installation usually decide how well the system works.

Start with gain. Always check whether it is quoted in dBd (relative to a half-wave dipole) or dBi (relative to an isotropic radiator). The difference is 2.15 dB, which is why some ads look generous. Gain in a vertical antenna is not free power. It comes from squeezing the pattern in elevation, so the antenna sends more energy toward the horizon and less up and down. That is useful on flat terrain or when you are talking to a distant repeater. It can hurt when you are in hills, on a steep slope, or very close to a repeater sitting well above you.

A quarter-wave whip is about 19 inches (roughly 48 cm) on 2 m. It needs a ground plane, and a vehicle roof is ideal. A 5/8-wave whip is longer and uses a loading coil or matching network at the base. In the ideal case it has roughly 3 dB more gain than a quarter-wave and a lower takeoff angle. It also depends more on a good ground plane, so a poor mounting location can erase much of that advantage.

The J-pole is an end-fed half-wave radiator with a quarter-wave matching stub. The Slim Jim is a similar idea with the structure folded. Both are roughly half-wave-class antennas, so be skeptical of claims of large gain. The less obvious issue is that they have no real ground plane. If the coax is simply hung from the bottom, the outside of the shield can carry current and become part of the antenna. That distorts the pattern and can change the SWR as you move the cable. A choke (ferrite beads or a few turns of coax) near the feedpoint helps, as does running the coax away from the antenna at a right angle where practical.

So the questions are these. What do you actually need: a compact omni, more reach toward a known repeater, or something you can take down and carry? And where does the antenna have to sit, on a roof, a mast, a balcony, or a vehicle? Pick the pattern for the geometry first, then pick the hardware.

  • Replies 2
  • Views 89
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the antenna types, I'd split them by what the pattern does rather than by name. A collinear is a stack of phased half-wave sections, usually vertical, so it is omnidirectional in azimuth with a flatter elevation pattern. A short one might give around 3 dBd, and longer ones more, but the longer the antenna, the narrower the vertical beam. That makes mounting height and mast plumbness matter more. If the mast leans or the antenna is mounted on a sloped roof, a high-gain collinear can point part of its beam away from where you need it.

A yagi is the opposite approach: you trade coverage for directivity. A three- or four-element yagi has useful gain and front-to-back rejection, which can help with a noisy side or a weak repeater in one direction. Polarization is the catch. Most FM repeater and simplex work is vertical, so a yagi for that has to be mounted with its elements vertical. Weak-signal SSB/CW work on VHF and UHF is traditionally horizontal. Cross-polarized stations lose a lot of signal in theory, often well over 10 dB in practice, though reflections and local conditions can soften that.

For mobile use, NMO is a good mount because it is mechanically solid and keeps the connection to the whip consistent. It needs a hole, so it is a commitment. A mag mount is quick and removable but depends on a flat metal surface under it, a clean contact, and a cable route that does not pinch the coax. Roof center usually gives the most symmetrical pattern. A trunk-lip mount can skew the pattern because the body blocks some directions. Dual-band mobile whips are often a compromise, with different effective gain on 2 m and 70 cm, so check the manufacturer's data for both bands.

  • Administrators

I'd put at least as much attention on the feedline and connectors as on the antenna, especially on 70 cm. Coax loss rises with frequency, and typical numbers are quite different between a thin cable and a better low-loss one. As a rough guide, RG-58-style cable loses several dB per 100 ft on 2 m and noticeably more on 70 cm, while LMR-400-class cable is much lower. Use the manufacturer's loss table for your exact cable, because brands and construction vary. A few dB of loss before the antenna means a few dB less signal on transmit and a worse receive noise figure too.

This is also why SWR can mislead. SWR tells you how well the antenna system is matched to the 50 ohm line. It does not tell you how much power is radiated. A lossy cable can improve the SWR reading at the radio because the reflected power is attenuated on its way back. So a low SWR with a long run of thin coax does not prove it is efficient. For reference, 1.5:1 SWR reflects roughly 4% of the power, 2:1 about 11%, and 3:1 about 25%, before accounting for cable loss. For FM voice, a modest SWR is not usually the main problem, but a bad one can make some radios fold back power.

On connectors, PL-259 (UHF) connectors are common and fine for HF and, in many cases, 2 m. They are not constant-impedance, so they are less suitable at 70 cm and above. N-type connectors are constant impedance, hold up better at UHF, and seal better outdoors when assembled correctly. Whichever you choose, a poor crimp or solder joint is a more likely failure than the connector family. Outdoors, weatherproof every joint properly, typically with self-amalgamating tape and a protective outer wrap. Water getting into coax is a common cause of slowly rising loss and a changing SWR.

For satellites, the key difference is polarization. Many amateur satellite signals are effectively circularly polarized in practice because the satellite is tumbling or spinning and the path geometry changes during a pass. Because of that, people often use circularly polarized or crossed-yagi antennas, or a handheld directional yagi like an Arrow-style antenna, and track the Doppler shift. For high passes, a simple vertical may work for some FM satellite contacts, but low passes and weak links benefit from gain and polarization flexibility.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.