Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From-scratch wire antennas: wire choice, chokes, ladder line, radials and modeling before you cut anything

ci_cover.jpg

This thread is for the decisions that matter before you cut wire for a homebrew dipole, inverted-V or vertical. The reference case is a 40 m dipole or inverted-V on a fiberglass pole or a tree, plus a 40 m quarter-wave vertical as the alternative. Most of the usual problems (a mystery SWR, RF in the shack, an antenna that drifts in frequency) come from the same few choices, so they're worth talking through first.

Wire: for HF dipoles, conductor resistance is a minor loss compared with ground, feedline and common-mode problems. Choose wire for strength and longevity. 14 AWG copper-clad steel or hard-drawn copper holds its length well. Soft-drawn copper stretches over time, and the resonant frequency drifts with it. Insulated wire resonates a few percent lower than bare wire of the same length because of the dielectric loading, so a bare-wire length from a formula will be off. The usual starting formula is about 468/f(MHz) feet for the whole dipole, which is only a starting point. Height, droop angle, nearby objects and wire type all move the result, so cut long and trim.

Hardware: use real insulators at the ends and center, such as UV-resistant plastic, ceramic or HDPE. Do not tie wire to a rope and rely on the rope as the insulator, especially when it's wet. Strain relieve the coax or ladder line so the weight doesn't pull on the solder joint. Tin and solder joints only where they aren't carrying tension, and seal any coax end against water. For an inverted-V, the center support needs to carry the feedline and the weight of the wire without bending. A pole that sways will change SWR a little in the wind.

What are people using for feedline and choke arrangements? Please say what you'd choose and why.

  • Replies 2
  • Views 35
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the feedline, the choke matters more than the balun label. A dipole fed with coax can have current on the outside of the shield, which distorts the pattern, pushes RF into the shack and changes the SWR reading depending on how the coax is routed. A 1:1 current balun or choke at the feedpoint is the standard fix. Ferrite beads or toroids on the coax, or coax coiled into several turns, can both work. The core mix has to suit the band. Type 31 is commonly used on the lower HF bands and type 43 higher up. The choke's impedance at the operating frequency matters more than the turn count, and an analyzer can show you whether it's actually working. A second choke at the shack end is cheap insurance if the feedline runs near other wiring.

If you use ladder line instead, the usual setup is 450 ohm window line or similar, run to a tuner. The line itself has very low loss even at a high SWR, so the loss comes from the tuner and any balun after it. Keep the ladder line a few line-spacings away from metal gutters or siding, and let it fall away from the antenna at right angles for a stretch rather than running parallel to the wire. Where it meets coax, put the choke on the coax side. A high-ratio balun on a very reactive load can overheat or lose a lot of power, so don't assume a 4:1 is automatically suitable.

For SWR measurement, an antenna analyzer at the feedpoint, with the choke in place, tells you far more than a meter at the shack. The R and X readings tell you whether the antenna is short or long, and the lowest SWR isn't necessarily the resonance. Be aware that strong AM broadcast stations can disturb readings on 160, 80 and sometimes 40 m. Test the analyzer into a known dummy load first.

  • Moderators

For the vertical, a quarter-wave on 40 m is about 33 ft (roughly 234/f in MHz, in feet), which is why a fiberglass pole is popular: it's a non-conductive support, and the wire is taped or clipped along its length. The radial system is what decides how well the antenna works. Ground-mounted verticals need many radials. Quantity beats precise length, and 16 or more is a reasonable minimum, with more being better. Elevated verticals can work with fewer, tuned radials, and sloping them downward raises the feedpoint resistance toward 50 ohms. A common-mode choke at the base is useful here too, since the coax shield can otherwise act as an extra radial.

Trap antennas are a trade-off. A parallel LC trap isolates the outer part of the wire on the higher band, which gives you multiband operation on one wire, but the traps add loss, narrow the bandwidth and need weatherproofing and voltage ratings suitable for the power level. For a first build, separate dipoles in a fan arrangement, or a single-band dipole with a tuner and ladder line, are usually easier to adjust than traps. Fan dipoles interact, so expect to trim in more than one pass.

For modeling, EZNEC (NEC-based) and MMANA-GAL (MININEC-based) are good for checking the idea before building. Pay attention to segmentation, particularly where wires join and near the feedpoint. Model the real height, ground type and wire loss, and use EZNEC's average gain test to check the model is sound. Neither tool will tell you about common-mode current unless you model the feedline too. Real ground effects for radials near or on the ground are better handled by a NEC-based program than by MMANA. Treat the model as a guide to trends, such as how much a change in height or droop moves the resonance, rather than as a precise answer. Then build it, measure it, and trim.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.