Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building an HF shack around a 100 W rig: where should the money and effort go first?

ci_cover.jpg

Rig comparisons usually center on the IC-7300 vs IC-7610, FT-991A vs FTDX10, TS-590SG vs TS-890S, and K3S vs KX3. They are fair debates, but the choice of transceiver often matters less to how a station performs than everything around it. So here is a framework for discussion, with points to push back on.

Start with the receiver side. Dual-receiver rigs like the IC-7610 or K3S (with its sub-receiver option) help with split-frequency work, contesting and DXpedition pileups. In a single-operator shack with one antenna, a second receiver is less useful than a well-behaved noise floor. On a typical suburban lot, local noise from LED lighting, switch-mode chargers, powerline hardware and the shack's own computers often sets the limit, not the radio's sensitivity. Good dynamic range matters when strong stations are nearby on the same band, such as in contests or Field Day. For quiet-band listening, a better antenna or a receive-only loop usually helps more than a more expensive rig.

Then power. A 100 W transceiver can draw roughly 20 A or more on transmit peaks at 13.8 V, so a 25-30 A supply gives comfortable margin. Voltage sag under load can reduce output and distort SSB. A supply with a noisy switching regulator can show up as birdies or a raised noise floor on the lower bands. Heavy gauge DC cabling, short runs, and fuses at the supply end are all worth planning for. The G90 and KX3 are lower power (20 W and 10 W nominal, with the KX3 reaching higher output on external power), so the demands are lighter, but supply noise still matters on a sensitive receiver.

Next, the tuner and amplifier chain. The internal ATU on a typical 100 W rig is built to correct a modest mismatch, not to make a poor antenna system work. If an amplifier is added, the usual approach is to present it with a low SWR at its input, keep drive within its rating, and put any tuner after the amplifier if the antenna needs one, using a tuner rated for the power. Running an amp into a high SWR can stress its output network or its protection circuits.

Band-pass filters are the least understood part of the chain. For a single station with one transmitter, they are often unnecessary. In multi-transmitter setups, such as SO2R or Field Day, they help prevent a transmitter on one band from overloading the receiver on another. They add a little insertion loss and must be rated for the power through them. The question I would like to hear opinions on is when a BPF is a real fix and when it is just hiding a bonding or common-mode problem.

Finally, grounding and bonding, which gets mixed up with lightning protection and RFI control. There are at least three separate jobs: safety (AC equipment grounds and bonding to the electrical service per local code), lightning protection (bonding coax shields and ground rods at a single entry point, with arrestors or disconnects), and RF management (common-mode chokes at the feedpoint and where cables enter the shack, plus short bonding between equipment chassis). One long ground wire to a rod is not a good RF ground at HF, and it can act as part of an antenna. Which of these three problems do you try to solve first, and how do you tell whether an RFI problem is common-mode current on the coax or noise coming through the power lines?

  • Replies 2
  • Views 50
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put the order as antenna, then noise and common-mode control, then power, then the rig. A K3S or TS-890S won't beat a decent antenna system on a noisy band, and a lot of 'my receiver is deaf' problems come down to noise at the antenna, not the radio.

On power, a quiet 25-30 A supply with fuses, short heavy leads and a ferrite on the DC cable is cheap insurance. If the noise floor changes when you switch the supply off and run from a battery, you've found the noise source. A simple test that costs nothing is to move the supply and the computer power bricks away from the radio and compare the S-meter on a dead band.

For bonding, I'd separate the jobs the way you did. The AC safety ground and the lightning bond belong to the building's electrical system and need to follow local code, so it's worth asking a qualified electrician. The RF part is mostly about keeping the feedline from carrying common-mode current into the shack. A choke at the feedpoint and another near the entry point, plus keeping the coax from running parallel to AC cables, usually does more than adding ground rods. A test is to see whether touching or moving the coax changes the noise or the SWR, which suggests current on the outside of the shield.

  • Moderators

On the rigs, the useful questions are how you operate and what band conditions you have, not which model is 'best'. The IC-7610 and K3S make sense if you work split, chase DX or contest and benefit from two receive paths. The IC-7300, FTDX10 and TS-590SG fit a single-operator station well. The FT-991A is attractive if you also want VHF/UHF in the same box, though it's a compromise at the extremes of dynamic range. The G90 and KX3 are for portable use or low power, where weight and current draw matter more than a big front panel.

On band-pass filters, I'd say they solve a specific problem: strong out-of-band energy hitting a receiver, typically from another transmitter at the same site. They won't fix noise from LED lighting or a switching supply, and they won't cure common-mode current on the coax. If you're running one rig and one antenna, I'd diagnose the noise and the bonding first. If you're running two stations near each other, a BPF per radio is worth the cost, provided it's rated for the power through it.

One more point on amplifiers. Set the drive so the ALC isn't doing the work. Check the amp's input SWR rather than assuming the rig's tuner has made it a perfect load, and keep an external tuner after the amp if the antenna needs one. A clean 100 W signal into an amp usually sounds better than a pushed 100 W with the ALC in the red.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.