Building a ham go-kit that actually works: power, antennas, and what to do when the repeater is down
- Replies 2
- Views 116
- Created
- Last Reply
Top Posters In This Topic
-
Admin_Terry 1 post
-
Mod_Tom 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
Go-kit threads tend to turn into gear lists, but the kit matters less than the plan behind it. Here is a framework to pick apart. Tell me where it's wrong or what's missing.
Start with the job, not the gear. A kit for checking in on a local net from home is different from one for deploying to a shelter or staying mobile in a vehicle. Decide which of those you're actually building for, then size everything around it. A common split is a small grab-and-go bag (HT, spare battery, a better antenna, a notepad, a headlamp) and a larger "stay" kit (mobile or base radio, a battery, a charger, coax, a mast).
HT kit basics. The stock rubber duck is the weakest link. A roll-up J-pole or a longer replacement whip can noticeably improve what you can reach. Add a speaker-mic, a AA battery tray or a spare battery for each radio, charging cables, and a printed list of local repeaters and simplex frequencies. Don't rely on programming stored only in your phone or computer. Print the channel list and keep a copy in the bag. Also check that the radio is programmed with 146.520 and 446.000 simplex, since repeaters may be down or overloaded.
Backup power. A 12 V battery (LiFePO4 or AGM) with a fused distribution block is the center of most mobile and base kits. Put the fuse close to the battery, use wire sized for the load, and standardize on one connector type, such as Anderson Powerpoles, in the orientation your local group uses so gear is interchangeable. For solar, remember that a panel's open-circuit voltage is higher than its rated voltage, and it should go through a charge controller rather than straight to the battery. Test the whole chain in daylight before you need it, and note how many watt-hours you can actually use. Receive draw is small, but transmit on high power adds up quickly.
Antenna kit. Include a 2 m/70 cm option (J-pole or magnetic mount), an HF option if you operate HF (an end-fed or a simple dipole), 50 ft or so of coax with good connectors, a throw weight and cord, and an SWR meter or a nanoVNA. Pack adapters (BNC, SMA, PL-259) because mismatched connectors are a classic way to end up with a radio and antenna that can't connect.
GMRS, FRS, MURS, and weather radios. These cover the family and neighborhood side. FRS needs no license. GMRS does require an FCC license, though it covers your immediate family and allows higher power and repeaters. Your ham license doesn't authorize GMRS operation. MURS is license-free on five VHF channels and allows external antennas, which can help in some places. A NOAA weather radio with SAME alerts and battery backup is worth having, because it works when cell service and internet are not. Pick one channel and a check-in time for family radios, and write it down.
Family communication plan. Pick an out-of-area contact everybody can reach, since text messages may get through when voice calls don't. Choose two meeting places, one near home and one farther away. Put everyone's numbers on a printed card. If family members aren't hams, decide who monitors which radio and when. If any check-in is going to fail, it will be the one nobody rehearsed.
First aid and supplies. Water, food, medications, a first aid kit that matches your training, a light and spare batteries, a paper map, and a whistle. Training matters more than the contents: a first aid class beats a bigger kit.
Question for the thread: what do you test on a schedule, and what do you only assume works? Also, how does your local ARES group or net handle a fully grid-down scenario when the main repeater loses power?
Link to comment
https://www.hamradiobase.com/forums/topic/10922-building-a-ham-go-kit-that-actually-works-power-antennas-and-what-to-do-when-the-repeater-is-down/Share on other sites