Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Where do I actually operate? Band plans vs. FCC privileges, band edges, 60 m channels, and VHF/UHF calling frequencies

ci_cover.jpg

I'm trying to sort out the difference between what the FCC rules require and what the ARRL band plan only recommends. The band plan charts show CW, digital and phone segments from 160 m up through 33 cm, but I can't tell which lines are legal limits and which are just courtesy.

Specific questions:

1. Is the ARRL band plan enforceable, or only the Part 97 privileges by license class?
2. How close to a band edge can I put my dial frequency in SSB or a digital mode?
3. How do the 60 meter channels work, since they don't look like the other HF bands?
4. Which simplex calling frequencies should I know on 6 m, 2 m, 70 cm and 33 cm?
5. How do international allocations change things if I travel or work DX?

Corrections welcome. I'd like a mental model I can rely on, and I'll check current FCC text before transmitting anywhere near an edge.

  • Replies 2
  • Views 135
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the legal/voluntary split. Part 97 (mainly 97.301 to 97.313) sets which frequencies each license class may use, which emission types are allowed in which segments, and the power limits. Those are rules. The ARRL band plan is a voluntary agreement about how to share the space inside those limits. It's why FT8 clusters at 14.074 and SSB doesn't sit on top of the RTTY/data segment. Ignoring it won't usually draw FCC attention, but you'll get QRM and some pointed comments.

On privileges, the HF picture for a US licensee looks like this. Extra has all amateur frequencies. General has all of 160 m, 30 m, 12 m and 10 m (30 m is CW/data only, 200 W PEP). On 80, 40, 20 and 15 m, General is limited to parts of each band, and the Extra-only portions sit at the bottom of the phone and CW/data segments. For example, General phone on 20 m starts at 14.225 MHz and on 15 m at 21.275 MHz. On 80 m, General phone is 3.800 to 4.000, and on 40 m it's 7.175 to 7.300. Technicians get CW on parts of 80, 40 and 15 m, plus 10 m from 28.000 to 28.500 MHz (28.300 to 28.500 includes SSB phone), with a 200 W PEP limit on those HF segments. Above 50 MHz, Technician and General have essentially the same privileges as Extra. Advanced licenses are no longer issued, but existing holders keep their slightly larger sub-bands. Verify exact numbers against the current rules.

On band edges, the number that matters is the edge of your emission, not your dial. In USB, the signal extends upward from the displayed carrier frequency, by roughly 2.5 to 3 kHz for a normal voice signal. In LSB, it extends downward. So at the General phone edge on 75 m at 3.800 MHz, an LSB dial at 3.800 puts part of your signal in the Extra-only segment. Moving to about 3.803 or higher keeps the whole signal inside. At the top edge, such as 14.350 MHz, USB needs the dial a few kHz below that. Digital modes work the same way. FT8 dial frequencies like 14.074 are in USB with the audio tones adding a few kHz on top, so check where the actual signal lands. Leave a margin, because dial calibration isn't perfect either.

For HF convention, LSB is normally used below 10 MHz and USB above, with 60 m being a special case, covered in the next reply. Digital activity concentrates near calling frequencies (FT8 at 1.840, 3.573, 7.074, 10.136, 14.074, 18.100, 21.074, 24.915, 28.074), and PSK31 and RTTY use their own subsegments. On 160 m, the DX window is traditionally around 1.830 to 1.840 MHz, and phone sits higher in the band. Check the current ARRL band plan for exact boundaries, because they get revised.

  • Administrators

Picking up the other half: 60 m, VHF/UHF, and the international side.

60 meters isn't a band in the usual sense. In the US, amateurs have access to five specific channels, not a continuous range. The channel center frequencies are 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5 kHz. Because phone on these channels is USB, the dial frequency you tune is 1.5 kHz below center: 5332.0, 5348.0, 5358.5, 5373.0 and 5405.0 kHz. This is the most common 60 m mistake, so check which number your logging software or a chart is quoting. The channels allow phone, CW and certain data modes within a 2.8 kHz bandwidth, with a power limit of 100 W PEP ERP relative to a half-wave dipole. General and Extra licensees can use them, and the amateur service is secondary there. There is also a newer international allocation at 5351.5 to 5366.5 kHz from WRC-15, but how it is implemented varies by country, so check current FCC and local rules before assuming it applies.

On VHF/UHF, the useful simplex calling frequencies are:

6 m (50 to 54 MHz): 50.125 MHz is the SSB calling frequency, 52.525 is the FM simplex calling frequency, and 50.313 is the FT8 frequency. CW and beacons sit at the bottom.
2 m (144 to 148 MHz): 146.520 is the national FM simplex calling frequency, 144.200 is the SSB/CW weak-signal calling frequency, and 144.390 is APRS in North America. Repeater pairs are mostly 600 kHz offset (inputs and outputs in the 146.6 to 147.4 range), so stay out of the repeater subbands for simplex.
70 cm (420 to 450 MHz): 446.000 is the national FM simplex calling frequency, and 432.100 is the weak-signal calling frequency. Repeaters normally use a 5 MHz offset. This band is secondary, with geographic restrictions near some radar installations and near the Canadian border (Line A), so check 97.303.
33 cm (902 to 928 MHz): this is a Region 2 allocation, shared with ISM and Part 15 devices, and the amateur service is secondary. 903.100 MHz is a commonly used weak-signal calling frequency. Activity is far thinner than on 2 m or 70 cm, so check the current band plan for FM and repeater arrangements. Also be aware of the National Radio Quiet Zone restrictions.

On the international side, the ITU divides the world into three regions, and allocations differ by region and by country. A few examples: 80 m is 3.5 to 3.8 MHz in Region 1 but 3.5 to 4.0 in Region 2. 40 m is 7.000 to 7.200 in Regions 1 and 3 but 7.000 to 7.300 in Region 2. 2 m is 144 to 146 in Region 1 but 144 to 148 in Regions 2 and 3. 70 cm is 430 to 440 in Region 1 but 420 to 450 in the US. 6 m is not available everywhere in Region 1, and where it is, the allocation is often narrower. Individual countries then add their own restrictions. So when you work DX, expect stations in other regions to be listening in a different subband than the one you'd use at home, and you may hear split operation for that reason. If you plan to operate abroad, check the host country's rules, including whether your license is covered by a reciprocal agreement and which local class it maps to, rather than assuming your US privileges carry over.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.