Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small-yard HF antennas: how to compare EFHW, OCFD, G5RV, doublet and vertical options without trusting SWR alone

ci_cover.jpg

A common small-lot question goes: "I have about 50 to 70 feet of usable space, a couple of tall supports or a tree, and an HOA that dislikes anything obvious. What should I put up?" The answers usually turn into a fight between EFHW, OCFD, G5RV, doublet and vertical camps, and the argument is usually about SWR. SWR is a poor way to rank antennas, so here is a framework for the comparison.

SWR only tells you how well the load at the end of the feed line matches the line and radio. A dummy load is a perfect 1:1 and radiates nothing. A short, lossy antenna can show a flat match while converting much of your power to heat. What matters for performance is radiation efficiency, pattern, takeoff angle and total system loss, and SWR affects only the last of these, through added feed line loss.

That loss is where coax choices matter. Coax loss rises with frequency and with mismatch. A short run of RG-213 at 14 MHz is nearly negligible even at a modest SWR. A long run of thin coax such as RG-58 on 10 meters feeding a 3:1 load can waste a noticeable share of your power. This is the strongest argument for balanced line (ladder line or window line) on multiband antennas that will be tuned far from resonance. A doublet or a G5RV-style antenna fed with ladder line and a good tuner can often beat a "resonant" antenna fed with long, lossy coax.

Height above ground is the next big factor, and it is easy to underrate. A horizontal dipole at 0.5 wavelength has a useful low-angle lobe for DX. At 0.15 to 0.25 wavelength it behaves more like an NVIS radiator, with a strong high-angle lobe and weaker low-angle signal. For example, a 40 m dipole at 30 ft is roughly 0.2 wavelength up and will work well for regional contacts, but it is not a great DX antenna. On 20 m the same wire is closer to 0.45 wavelength and the pattern improves. Inverted Vs trade some low-angle performance and bandwidth for needing only one tall support, and the ends can be tied off low. They need a slightly shorter wire than a flat-top dipole, and the feed impedance drops as the included angle tightens.

On the specific designs:

EFHW: a half-wave wire fed at one end through a high-ratio transformer (commonly 49:1 or 64:1). A 40 m version is resonant on 40, 20, 15 and 10 because those are harmonics, but 30 m and 17 m are not harmonically related and usually need a tuner or a different design. Because the feed is at high impedance, the current on the transformer's "ground" side has to go somewhere, so the coax shield often serves as a counterpoise. A common-mode choke at the radio end helps keep RF out of the shack. The wire end carries very high voltage, which matters for safety, especially at power or near people and pets. Transformer core losses and heating also vary a lot between builds.

OCFD (Windom-style): the feedpoint sits roughly a third of the way along the wire, with a 4:1 current balun or similar. A 40 m-based OCFD can work on 40, 20, 10 and sometimes 15 m, but the impedance and pattern vary by band and the match is rarely perfect everywhere. Common-mode current on the coax is a frequent complaint, so a good choke is worth having.

G5RV: roughly 102 ft of dipole fed with a matching section of ladder line, then coax. It was designed around 20 m, where the matching section acts like a useful length. On other bands it is essentially a doublet that needs a tuner. The half-size 51 ft version is popular for small lots but covers lower bands less efficiently. It is a reasonable compromise, but not a magic multiband resonant antenna.

Doublet: a flat-top of arbitrary length fed with ladder line into a balanced tuner or a tuner with a good 4:1 or 1:1 balun. Avoid lengths that give extreme feedpoint impedance on your favorite bands, where the tuner and line may see very high voltage or current. It is a flexible, low-loss and often underrated option.

Trap dipoles and other loaded antennas: traps shorten the antenna and make multiband use convenient, but they narrow bandwidth and add loss compared with a full-size dipole on each band. They are a good solution for tight spaces, though not free of compromise.

Verticals: a ground-mounted quarter-wave vertical depends heavily on its radial field. Many buried or surface radials improve efficiency, and a handful will work but at lower efficiency. An elevated vertical with several tuned radials (often 2 to 4 per band, sloped or horizontal) can work well with fewer wires, and the feed impedance is closer to 50 ohms when radials slope downward. Verticals tend to give a lower takeoff angle, which is good for DX, but they can be noisier on receive and weaker on near-in contacts than a horizontal wire.

Loops: a full-wave horizontal loop is a very good small-yard antenna if you can support the perimeter, since it has good efficiency and relatively low noise. A magnetic loop is a different animal: a small, high-Q loop with a variable capacitor. Efficiency depends on conductor size, joint quality and capacitor losses. Bandwidth is very narrow, so you retune when you move a few kHz, and the capacitor sees very high voltage. It can be useful where nothing else fits, but it is a compromise antenna.

Yagis and other beams: gain and front-to-back ratio are the prize, and even a three-element beam can add several dB over a dipole, but you need a tower or mast, a rotator, and permission. For HOA situations a small beam is rarely the first thing to try.

For stealth installations, thin dark wire between trees, a flagpole-style vertical, an attic dipole, or a wire along a fence line can be nearly invisible. Attic antennas are subject to losses from nearby wiring, ducts and insulation, and any antenna close to living space needs thought about RF exposure and interference to household electronics.

Where would you start if you had one 60-ft run and a single 30-ft support? Would you go with a resonant dipole or inverted V, an EFHW, or a doublet with ladder line and tuner?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

With one 30-ft support and about 60 ft of run, a doublet or a shortened dipole fed with ladder line is hard to beat for flexibility. A roughly 60-ft flat-top is close to a half-wave on 80 m only if you stretch it, so think of it as a good performer from 40 m up and a compromise on 80/160 m. Feed it with ladder line and a balanced tuner (or a tuner with a good 4:1 balun) and keep the ladder line away from metal for the first several feet. Avoid choosing the length purely for resonance on one band; check the modeled feedpoint impedance for each band you care about, because some lengths put you at very high impedance on a band you plan to use and make the tuner struggle.

If you must use coax, a simple resonant inverted V for a single band plus a decent choke is much more predictable than a multiband design that depends on the tuner. SWR can be flat, but the pattern from a low inverted V on 40 m will still be mostly high-angle.

  • Moderators

One thing to add on the EFHW: the "no tuner, no radials" pitch is only partly true. The transformer needs something to push against, and in many installs that something is the coax shield. If the coax run is an odd fraction of a wavelength on some band, the common-mode current changes and so does the SWR, and RF can show up in the shack. A choke near the feedpoint or near the radio, or a purpose-made counterpoise wire, usually makes the antenna behave more predictably. Also check how the transformer is rated. A 49:1 unit handling 100 W SSB is a different job from the same unit handling 100 W of FT8 or RTTY, and some compact cores can get warm.

For verticals, if you cannot lay many radials, elevated tuned radials are worth considering over a handful of short ground wires. Four radials raised a few feet can outperform a few buried ones, and they are easier to hide at the edge of the lawn than a field of surface wires.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.