Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a 5 W portable station: rig choice, antenna, and power for QRP CW and SSB

ci_cover.jpg

I'd like to compare notes on putting together a practical 5 W portable setup. QRP is usually defined as 5 W output on CW and 10 W PEP on SSB. QRP-ARCI also recognizes milliwatting at 1 W or less. The rule matters less than the question behind it: which parts of the system actually decide whether you make contacts?

The usual argument is that going from 5 W to 100 W is about 13 dB. That is a bit over two S-units on a receiver calibrated at 6 dB per S-unit, and it's a lot to give up. But a poor antenna can easily cost you 5 to 10 dB in loss or bad takeoff angle, so the antenna and the operating habits often count for more than the rig. Time of day, band choice and calling technique also have an outsized effect.

On rigs, there seem to be three broad camps. The first is the full-featured portable transceiver such as the Elecraft KX2 or KX3. They cover CW, SSB and digital modes on multiple bands, with a good receiver and optional internal ATU and battery. The KX3 puts out a bit more power if you want it, but 5 W is the QRP sweet spot for battery draw. The second is the minimalist CW rig, like the Mountain Topper family or the Penntek TR-35. These are small and light, draw little current, and are built around the CW-only summit or park workflow. The third is the kit and homebrew route: Hendricks-style kits, Pixie-type transceivers, and single-band designs you build over a few evenings. The Pixie in particular is a famously simple design, and it makes a great learning project. Its receiver is wide and not very sensitive, though, so I'd call it a build-and-learn project, not a primary field rig.

For calling frequencies, the commonly cited QRP centers of activity are around 3.560, 7.030 (7.040 in some regions, so check your band plan), 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz on CW. For SSB the usual ones are around 3.985, 7.285, 14.285, 21.385 and 28.385 MHz. These aren't protected frequencies. They're places where people expect to hear low-power stations, so check the current band plan for your region before relying on any of them.

For power, a small LiFePO4 pack is attractive. Nominal voltage is about 12.8 V for a 4-cell pack, it has a flat discharge curve, and it's light for the capacity. The thing to check is the full-charge voltage, which can be around 14.4 to 14.6 V. Look at your rig's maximum input spec before connecting, and make sure the pack has protection and fusing. Some rigs are happy at 13.8 V nominal but have lower ceilings, so don't assume.

For antennas, the common choices are an end-fed half-wave with a 49:1 transformer, a linked dipole, an inverted V on a light mast, or a compact vertical with radials or a counterpoise. Each has tradeoffs in setup time, band coverage and tuner needs.

What is your minimum kit for a portable QRP outing? And what single thing made the biggest difference to your results: the rig, the antenna, the band or the operating technique?

  • Replies 2
  • Views 38
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd put the antenna first and the rig second, and I'd say that even before talking about brands. A resonant, well-elevated wire that gets the radiation up and away from ground will usually do more than any change inside the radio. An inverted V or linked dipole that is actually resonant is also kind to a small rig, because the radio sees a low SWR and you don't need an ATU eating up some of your 5 W.

An end-fed half-wave is convenient, but be honest about its weak points. The matching transformer and coax can add loss, and the feedline often becomes part of the radiating system. Common-mode current on the coax can hurt receive noise and change the pattern. A choke near the feedpoint is cheap insurance. A ten-minute test with a field strength meter or a quick A/B comparison against a simple dipole can be revealing.

On rig choice, the KX2 and KX3 give you SSB and a good receiver, but the lightweight CW-only rigs have a real advantage if your outings are hiking-based and CW-only. Fewer features means fewer things to carry, power and fail. If you only work CW, the saving in weight and current draw may matter more than features you won't use.

  • Administrators

One thing I'd add about the kit and Pixie side of this: building is a legitimate reason to do QRP, not just a way to save money. A Pixie-style rig teaches you how a transmitter, keyer and receiver detector work together, and it's quick to build. Just expect the receiver to be broad and prone to overload from strong signals. If you're after contacts rather than learning, a more selective design or a commercial kit will be less frustrating.

On LiFePO4, I'd double-check the voltage window at both ends. A fully charged pack can sit above 13.8 V, which is fine for many rigs but not guaranteed for all. At the low end, the flat curve means the voltage doesn't give you much warning before the protection circuit cuts off. A small voltmeter inline, or a rig that displays supply voltage, makes this easier to manage. Also, if your rig draws only a few hundred milliamps on receive, a small pack lasts much longer than people expect. So size the battery from current draw and operating time, and don't just buy the biggest cell you can carry.

For operating, use the calling frequencies as a starting point, but also tune around and answer CQs. With 5 W you'll often have better results calling a station that is already listening than sitting on a frequency and hoping. Short exchanges, a clean CW fist and patience with repeats make a big difference. If you're interested in contests, QRP-ARCI-related activity is a good way to find other low-power stations.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.