Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From FM birds to linear transponders: sorting out Doppler, antennas and tracking for a first LEO setup

ci_cover.jpg

This thread is meant to collect practical notes on the usual progression in amateur satellite work. People tend to start with handheld FM passes, then move to linear transponders like RS-44, and some add QO-100 as a geostationary contrast. Each step changes what matters most: pointing, Doppler, sideband handling, or link budget. Please correct anything below and add your own tips.

FM birds are the easiest entry point. The FM satellites and the ISS cross-band repeater use a single-channel, half-duplex-style workflow. The ISS voice repeater has typically used 145.990 MHz up with a 67 Hz CTCSS tone and 437.800 MHz down, and ISS APRS is on 145.825 MHz. FM satellites such as SO-50, AO-91 and AO-92 have their own uplink and downlink pairs and access-tone requirements. Frequencies, tones and operating status change, and the ISS gear is not always configured for voice. Check a current source such as AMSAT before relying on any number. The key point is that FM is a one-QSO-at-a-time channel. Exchanges are short, usually callsign plus 4-character grid square, such as FN31, and many operators call only after hearing the pattern of who is active.

Doppler is the first thing that separates satellite work from terrestrial work. For a typical LEO pass the shift is on the order of a few kHz on 2 m and roughly 10 kHz either side on 70 cm. It is largest at the start and end of a pass, and it crosses zero near closest approach (TCA). On FM you can often get by with stepping the receive frequency in 5 kHz increments through the pass. On SSB and CW, manual tuning is practical but demanding, so many people let software drive the rig.

Gpredict and SatPC32 both handle prediction and rig control. Gpredict can send Doppler-corrected frequencies to supported radios and can drive a rotator through Hamlib's rotctld. SatPC32 is Windows software that works with the AMSAT-DK FODTrack ecosystem for rotator control and has its own radio interfaces. Either way, your TLE/Keplerian elements must be fresh, since stale elements are a classic reason a pass seems off in time or Doppler. Also verify your station grid and system clock accuracy.

On antennas, an Arrow-style handheld dual-band Yagi with a duplexer is a common choice for FM LEO because the pass is short and you can aim by hand. Beam width and polarization loss then become part of the workflow, and handheld operators often tilt or rotate the antenna to compensate for fading. For linear work with RS-44, more gain and steady pointing help. Because RS-44 is in a much higher orbit than the typical amateur LEO, its passes are long and Doppler changes more slowly, which makes it good for learning to track an inverting linear transponder. Larger Yagis on an az/el rotator are common, but a handheld Arrow can still work for strong passes.

QO-100 is a different problem. It is geostationary, so there is no Doppler and no tracking, but you need a dish, a suitable feed and a stable LNB, plus enough uplink power at 2.4 GHz. It is a good example of how the challenge moves from motion to frequency stability and precise pointing.

Questions to get started: What would you tell someone to buy or build first? When do you stop doing manual Doppler and move to CAT control? And what is the most common failure you see when someone's first pass produces nothing?

  • Replies 2
  • Views 82
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For a first station I would separate the problems. First, make sure you can hear the bird. Use a pass prediction with a decent maximum elevation, ideally one that is not too low on the horizon, and spend a few passes only receiving. That tells you whether your pointing, polarization handling and receive chain are working before you add transmit complications.

The most common FM mistake is probably the uplink tone or the uplink frequency, not the antenna. If a satellite needs a CTCSS tone for access, you have to set it correctly on the transmit side. A lot of people also forget to correct for uplink Doppler. The downlink shift is more obvious because you hear it, but the satellite hears your uplink offset too. A small mismatch can mean the satellite hears you weakly or not at all.

With an Arrow, a duplexer and an HT, take care with cable routing and the way you hold the antenna. Body proximity and cable pickup can distort the pattern. Rotating the antenna slightly can matter as much as aiming exactly at the satellite.

  • Moderators

On linear birds, the part that trips people up is inversion. In an inverting transponder, tuning your uplink higher moves the downlink lower, and sideband flips too, so an upper-sideband uplink appears as lower sideband on the downlink. A rig with split operation and software Doppler control helps, but you still need to understand what the software is doing. Otherwise you can end up chasing your own signal around the passband.

A practical approach is to find the beacon or a strong CW signal, set the downlink to a reference point, then transmit a short carrier or a few words and adjust until you hear yourself on frequency. Keep your power moderate. Linear transponders are shared, and an overdriven uplink can suppress other stations. Listen to the passband before transmitting, and keep calls short.

For software, I would pick Gpredict if you want a free, cross-platform tracker with Hamlib support, and SatPC32 if you are already in the Windows ecosystem and want its rig and rotator integrations. Whichever you choose, test the rotator on its own before relying on a live pass. Check azimuth wrap, elevation limits and any overlap or stop at north, since a rotator that swings the long way at the wrong moment can cost you half a pass.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.