Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bring-up order for a first homebrew QRP transmitter: what to check before an antenna is connected

ci_cover.jpg

Many kit and scratch-built rigs fail at the first power-up because the builder skipped steps, not because the design is bad. Here is the order I would use for anything from a Tuna Tin 2-style crystal transmitter to a BITX or uBITX build, and I'd like to hear what others would change.

1. Check the board before power. Look over every joint with magnification. You are checking for bridges, cold joints, reversed electrolytics and diodes, and transistors in the wrong orientation. Then use the meter's continuity range to confirm the supply rail is not shorted to ground. A few ohms with a slowly rising reading is usually just capacitors charging. A dead short is a reason to stop.

2. Use a current-limited supply. A bench supply with the limit set just above the expected idle current is the cheapest insurance you can buy. If you don't have one, put a 47 to 100 ohm resistor in series with the supply for the first power-up and watch the voltage drop across it. A receiver or low-power oscillator stage should draw a modest, steady current. If it climbs or the part gets warm, switch off and look again.

3. Never key into nothing. Put a 50 ohm dummy load on the output before the first transmit test. For a 1 W rig the numbers are easy: 1 W into 50 ohms is about 7.1 V RMS, or roughly 20 V peak-to-peak. At 5 W it is about 15.8 V RMS, or roughly 45 V peak-to-peak. Use non-inductive resistors, such as several metal film or carbon composition parts in parallel, and make sure their combined dissipation is well above what you apply. A simple RF probe with a diode and capacitor on a DMM can give you a rough power estimate. A scope across the load is better.

4. Verify the frequency and the keying. A frequency counter is ideal. A general-coverage receiver or an SDR with a small pickup wire also works. For a crystal-controlled rig like a Tuna Tin 2, confirm that the oscillator runs on the crystal's frequency and not some stray overtone. For a Pixie-style rig, remember that the transmit frequency and the receive frequency are tied together. Listen to your own signal on a second receiver for chirp, drift and key clicks. Slow the keying edges a bit with an RC network or a shaping circuit if the clicks are harsh.

5. Look at the harmonics. A single-transistor power stage can put out a lot of harmonic energy. The output low-pass filter is part of the transmitter, not an optional accessory. Without a spectrum analyzer you can still do a basic check. Tune a second receiver to the second and third harmonic frequencies with the transmitter running into the dummy load. Ideally you would measure with a proper analyzer or SDR and attenuator. Check what your licence conditions require for spurious emissions.

6. Build the SWR bridge and check it. Before you trust any SWR bridge, test it with known loads. A good 50 ohm load should show a very low reflected reading. A 100 ohm load (made from two 50 ohm resistors in series) or a 25 ohm load (two in parallel) should read close to 2:1. An open circuit and a short should both show near-full reflected reading. If the bridge misreads those, the antenna reading will not be reliable either.

7. Only then use an antenna. Start with low power, listen on frequency for activity, and keep the first contacts short while you check for spurious signals or a hot enclosure.

What other steps belong on this list, and what test equipment gave you the most value per pound or dollar spent?

  • Replies 2
  • Views 71
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd add something for the receiver side, especially a direct conversion receiver. Once the transmit side works, check for AM broadcast breakthrough, hum and microphonics. A simple direct conversion receiver with a diode ring or NE602 mixer and no RF selectivity can pick up strong out-of-band stations. If you hear broadcast audio on top of everything, a band-pass filter or at least a low-pass or high-pass section ahead of the mixer often helps.

Power supply noise matters a lot here too. A cheap switching wall adapter can put birdies or a buzz across the band. Try running the receiver from a battery as a test. If the noise disappears, you have found the cause. Then you can add ferrite chokes and bypass capacitors on the supply line, or move to a linear regulator.

For testing sensitivity without a signal generator, a crystal oscillator with a long attenuator chain or a very short wire coupling can give you a repeatable weak signal. It won't be a calibrated measurement, but it is enough to tell whether a change to the audio gain or mixer bias helped.

  • Moderators

For BITX and uBITX builds I'd put the filters and the output stage at the top of the checklist. These are fun, capable designs, but the transmitter chain is fairly broad, and the stock low-pass filters are only as good as the toroids and capacitors you actually built. If you wind the toroids yourself, check the inductance with a meter if you have one. If not, count turns carefully and compare with the instructions for your exact kit revision. Different kit versions have changed over time, so use the documentation that matches your board.

It's also worth looking at the output on an SDR or analyzer if you can reach one, rather than just trusting the power meter. Check each band you plan to use, because a filter that looks fine on one band can leave strong harmonics on another. Don't drive the final stage harder than it needs. A cleaner 5 W is better than a dirtier 10 W.

On accessories, a basic iambic keyer is a good first project because it is small, forgiving and testable on the bench. Use a pull-up on each paddle input, debounce in software or with a small capacitor, and check that the keying line only switches the transmitter's key input and doesn't carry RF back into the keyer. A small ferrite bead on the cable often cures odd keyer behaviour on transmit.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.