ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Repeater basics to linked systems: offsets, tones, timers, and who gets to use what
Questions about repeaters tend to repeat themselves: why can I hear the machine but not get into it, why does the repeater key up but nobody hears me, what does the tone setting actually do, and why did that conversation suddenly drop into a net across the country? This thread is a shared reference for the basics and for how linked systems change the etiquette. Rules and band plans differ by country, so correct me where your region does things differently.
Offsets and programming. A repeater listens on one frequency (its input) and retransmits on another (its output). Your radio listens on the output and transmits on the input. The offset is the gap between them, and the standard values depend on the band and the region. In North America, 2 m is usually 600 kHz, 70 cm is usually 5 MHz, and the sign depends on where in the band the output sits. Other regions use different splits, and 6 m, 1.25 m and 10 m have their own conventions. Always check the local band plan or the repeater's listing instead of assuming. Most radios have a reverse button that swaps your transmit and receive frequencies. It is a quick way to check whether you can hear a station directly (talkaround) and should move to simplex.
CTCSS, PL, DCS and tone squelch. CTCSS is a sub-audible tone sent along with your voice. "PL" is just Motorola's trade name for it. Many repeaters require the correct tone on their input before they will open up. That is separate from whether the repeater sends a tone on its output. On most radios, "Tone" mode only encodes (it sends the tone when you transmit), while "TSQL" or tone squelch encodes and also decodes, so your speaker stays quiet unless the received signal carries the matching tone. A common mistake is setting TSQL for a repeater that doesn't transmit a tone, which gives you silence. DCS does the same job with a digital code, usually written as a three-digit octal number, and it has its own quirk: some radios let you invert the polarity, so a mismatch can cause one-way problems. Tones and codes help keep out interference and stray signals. They are not security or privacy, because anyone can turn the tone off on their own radio and listen.
Time-out timers and basic etiquette. Most repeaters have a time-out timer (TOT) that drops the transmitter if you hold the key down too long, commonly somewhere in the one-to-three-minute range, though it varies. Keep your overs short and leave a second or two between transmissions. That gap lets the timer reset and gives someone with an urgent need a chance to break in. Listen before you transmit. Identify with your callsign as your licence conditions require (the details vary by country). You don't need to call "CQ" on a repeater. A simple callsign and "monitoring" or "listening" is enough. Avoid kerchunking, which means keying up just to see if you hit the machine.
Open, closed, and coordinated. An open repeater can be used by any licensed amateur who follows the rules. A closed or limited-access repeater is restricted to members, donors, or people who've been given the access tone or code. A repeater that needs a tone is not automatically closed. Many open machines simply require CTCSS. If you aren't sure, check the club's listing or ask the owner. In many countries, repeater frequencies are coordinated through a regional body or a national society, which reduces interference between systems. Coordinated pairs are typically the ones you can rely on to be protected, and the details depend on where you live.
Linking systems. There are two broad families. The first connects analog repeaters over the internet: EchoLink (callsign-validated, with node numbers, and the -L and -R suffixes usually indicate simplex links and repeater links), IRLP (DTMF-controlled node numbers and reflectors), and AllStar (open-source, Asterisk-based, node numbers, and hubs that tie lots of nodes together). The second family is digital voice networks: Wires-X (Yaesu System Fusion, with nodes and rooms), DMR (timeslots, color codes, talkgroups, and your own radio ID), and D-STAR (callsign routing, reflectors, and a gateway). Each has a different user interface, but the etiquette is similar: find out whether the repeater is linked before you start a long conversation, and don't connect or disconnect a link unless you know the owner's policy.
Directories and clubs. Online directories, printed repeater books, and regional coordinator lists are good starting points, but entries can be out of date, so verify tone, offset, and access policy against the club's own page before you rely on them. Clubs that run repeaters often welcome members and donations, and many publish their linking rules, net schedules, and control-operator contacts.
Questions to get started: how do you handle linked-repeater delay and the dropped first syllable? What do you do when a system doesn't list its access tone? And is there a better way to tell newcomers about timers than "wait for the courtesy tone"?
Questions about repeaters tend to repeat themselves: why can I hear the machine but not get into it, why does the repeater key up but nobody hears me, what does the tone setting actually do, and why did that conversation suddenly drop into a net across the country? This thread is a shared reference for the basics and for how linked systems change the etiquette. Rules and band plans differ by country, so correct me where your region does things differently.
Offsets and programming. A repeater listens on one frequency (its input) and retransmits on another (its output). Your radio listens on the output and transmits on the input. The offset is the gap between them, and the standard values depend on the band and the region. In North America, 2 m is usually 600 kHz, 70 cm is usually 5 MHz, and the sign depends on where in the band the output sits. Other regions use different splits, and 6 m, 1.25 m and 10 m have their own conventions. Always check the local band plan or the repeater's listing instead of assuming. Most radios have a reverse button that swaps your transmit and receive frequencies. It is a quick way to check whether you can hear a station directly (talkaround) and should move to simplex.
CTCSS, PL, DCS and tone squelch. CTCSS is a sub-audible tone sent along with your voice. "PL" is just Motorola's trade name for it. Many repeaters require the correct tone on their input before they will open up. That is separate from whether the repeater sends a tone on its output. On most radios, "Tone" mode only encodes (it sends the tone when you transmit), while "TSQL" or tone squelch encodes and also decodes, so your speaker stays quiet unless the received signal carries the matching tone. A common mistake is setting TSQL for a repeater that doesn't transmit a tone, which gives you silence. DCS does the same job with a digital code, usually written as a three-digit octal number, and it has its own quirk: some radios let you invert the polarity, so a mismatch can cause one-way problems. Tones and codes help keep out interference and stray signals. They are not security or privacy, because anyone can turn the tone off on their own radio and listen.
Time-out timers and basic etiquette. Most repeaters have a time-out timer (TOT) that drops the transmitter if you hold the key down too long, commonly somewhere in the one-to-three-minute range, though it varies. Keep your overs short and leave a second or two between transmissions. That gap lets the timer reset and gives someone with an urgent need a chance to break in. Listen before you transmit. Identify with your callsign as your licence conditions require (the details vary by country). You don't need to call "CQ" on a repeater. A simple callsign and "monitoring" or "listening" is enough. Avoid kerchunking, which means keying up just to see if you hit the machine.
Open, closed, and coordinated. An open repeater can be used by any licensed amateur who follows the rules. A closed or limited-access repeater is restricted to members, donors, or people who've been given the access tone or code. A repeater that needs a tone is not automatically closed. Many open machines simply require CTCSS. If you aren't sure, check the club's listing or ask the owner. In many countries, repeater frequencies are coordinated through a regional body or a national society, which reduces interference between systems. Coordinated pairs are typically the ones you can rely on to be protected, and the details depend on where you live.
Linking systems. There are two broad families. The first connects analog repeaters over the internet: EchoLink (callsign-validated, with node numbers, and the -L and -R suffixes usually indicate simplex links and repeater links), IRLP (DTMF-controlled node numbers and reflectors), and AllStar (open-source, Asterisk-based, node numbers, and hubs that tie lots of nodes together). The second family is digital voice networks: Wires-X (Yaesu System Fusion, with nodes and rooms), DMR (timeslots, color codes, talkgroups, and your own radio ID), and D-STAR (callsign routing, reflectors, and a gateway). Each has a different user interface, but the etiquette is similar: find out whether the repeater is linked before you start a long conversation, and don't connect or disconnect a link unless you know the owner's policy.
Directories and clubs. Online directories, printed repeater books, and regional coordinator lists are good starting points, but entries can be out of date, so verify tone, offset, and access policy against the club's own page before you rely on them. Clubs that run repeaters often welcome members and donations, and many publish their linking rules, net schedules, and control-operator contacts.
Questions to get started: how do you handle linked-repeater delay and the dropped first syllable? What do you do when a system doesn't list its access tone? And is there a better way to tell newcomers about timers than "wait for the courtesy tone"?
Link to comment
https://www.hamradiobase.com/forums/topic/10945-repeater-basics-to-linked-systems-offsets-tones-timers-and-who-gets-to-use-what/Share on other sites