Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning an HF shack around a 100 W rig: power, grounding vs. bonding, filtering, and where the RFI actually comes from

ci_cover.jpg

This is a discussion starter for anyone putting together or reworking a base station around one of the common 100 W transceivers (IC-7300, IC-7610, FT-991A, FTDX10, TS-590SG, TS-890S, K3S), or a lower-power rig like the KX3 or Xiegu G90 running barefoot or behind an amplifier. The radios differ a lot in receiver architecture and features, but the problems around them are surprisingly similar: a noisy supply, common-mode current on the coax, USB and audio loops, and confusion about what a ground is supposed to do.

Here are a few areas worth comparing notes on.

Power supply. A 100 W HF rig on SSB or CW is usually specified for about 20 to 22 A at 13.8 V on transmit, so a 25 to 30 A supply gives some headroom, and the voltage under load matters as much as the label. Cheap switching supplies are a common source of broadband hash on the lower bands, and the noise can be conducted on the DC leads as well as radiated. Ferrite chokes on the DC cable, short heavy-gauge leads, a fuse close to the source, and Powerpole distribution all help. Comparing the noise floor with the radio on battery versus on the supply is a quick way to tell whether the supply is the culprit.

Grounding versus bonding. These get lumped together but do different jobs. Safety bonding ties metal enclosures and the station's ground system to the building's electrical service ground, so a fault or a lightning-induced potential difference doesn't appear between pieces of equipment. Lightning protection means a single-point entry panel where coax shields and control lines are bonded outside the house and tied to a ground rod that is itself bonded to the service ground. An RF ground is a separate concept, and a rod outside the window is rarely a good one at HF. If RF is showing up on the mic, keyer, or computer, the fix is usually common-mode suppression on the feedline and a well-matched antenna system, not more ground rods. Local electrical codes differ, so check yours before doing anything involving the service panel.

Common-mode current. A choke at the feedpoint and another where the coax enters the shack often does more for RFI than any change inside the shack. A single-band antenna with a balun that actually presents high common-mode impedance behaves differently from a multiband wire fed with coax and no choke. Chokes on USB, CAT, audio, and keying leads are also worth adding, especially on the IC-7300 and IC-7610, where one USB cable carries CAT and audio to the computer.

Tuners and amplifiers. Internal tuners on rigs like the IC-7300, FT-991A, and G90 only cover a limited mismatch range. A tuner doesn't remove mismatch loss in the feedline, it just presents a friendlier load to the transmitter. With a linear amplifier, the usual setup is rig into amp, amp into tuner, tuner into antenna, with the drive level set so ALC is not active and the amp-keying line verified before any power is applied. Tuning a tuner with the amp in standby, or at low drive, saves relays and finals.

Band-pass filters and receivers. BPFs matter most when more than one transmitter is close by (multi-op contest stations, or a second radio on a nearby band), because the offending signal is strong enough to overload the front end of the receiver. They add some insertion loss and must be rated for the power and the SWR they will see. For a single-operator shack, a good roofing filter and attenuator or preamp management in the radio may be enough. Direct-sampling radios (IC-7300, IC-7610) and conventional superhets with narrow roofing filters (TS-590SG, TS-890S, K3S) have different overload behavior, which affects whether a preselector or BPF is needed. A dedicated receiver or RX antenna input can also help for low-band listening.

Layout. Keep RF-carrying cables away from audio, USB, and power wiring and cross them at right angles where possible. Use short jumpers between the rig, tuner, and amp. Put power distribution and the station ground bus where they can be inspected, and label coax at both ends.

Where do people here usually find the problem when they have a noisy shack: the supply, the antenna system, or a computer or USB device?

  • Replies 2
  • Views 92
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

It's worth separating noise that is received from noise that is transmitted. Receive noise on 80 and 40 m is often a switching supply, LED lighting, or a nearby charger. A simple check is to run the radio from a battery, or to switch off breakers one at a time with a portable receiver, and watch the S-meter or the waterfall. That narrows it down quickly.

On transmit, RF in the shack is almost always common-mode on the coax or on an end-fed or off-center antenna with no real counterpoise. Symptoms like a hot mic, a keyboard locking up, or USB audio dropouts point to this. Chokes with enough turns for the band, and sized to give high impedance on the lower frequencies, are better than one generic snap-on near the radio. Adding more ground rods rarely fixes this.

One more point on grounding: bonding the station to the service ground is a safety step and shouldn't be skipped for an outside ground rod alone. Tying the two grounds together reduces the risk of voltage differences across equipment during a surge.

  • Moderators

On radio choice and filtering, it helps to ask what the strong-signal problem actually is before buying a filter. If the issue is overload from a local broadcast station or a neighbor on a close band, a high-pass or band-reject filter at the antenna input may do more than a full BPF set. If it's a second transmitter on the same site, the BPF on each radio, or at least a stub or filter on the harmonics, is the usual solution. Filter specs for insertion loss, power rating, and rejection on the adjacent band should be checked against the actual use case.

The comparison between radios is more nuanced than direct-sampling versus superhet. The IC-7610's dual receivers and the roofing filter options on the TS-890S and K3S are advantages when conditions are crowded. The G90 and KX3 have fewer controls for dealing with overload, but at 20 W or 10 W they often work in less demanding environments, and the amplifier and external tuner arrangement can matter more than the radio. I'd check each radio's measured performance from independent lab tests and not rely only on the brochure specs.

For amplifiers, I would also verify that the radio's ALC and output power settings match what the amp needs. A rig set to full power into an amp that needs 50 W can produce splatter even when the SWR looks fine, and that is easy to miss without a monitor scope or a second receiver.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.