Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: how do you separate a power or PLL fault from a blown final or protection fault?

ci_cover.jpg

I'd like to compare approaches to the first hour of a repair, before anyone starts swapping parts or turning alignment slugs. "No transmit and no receive" and "no transmit but receive is fine" look similar on the bench, but they point to very different parts of the radio.

If both are dead, I'd think about what the two paths share: the DC input and internal regulated rails, the reference oscillator and PLL, the CPU or reset circuit, the antenna relay or T/R switching, and the band or mode switching lines. Start with the boring checks. Measure voltage at the rig's DC connector under load, not just at the supply terminals, then check the fuse, the reverse-polarity protection and the regulators. A fuse that looks intact can still have high resistance, and a loose power connector can drop enough voltage to make a rig act strangely.

If receive works and transmit doesn't, the list narrows: PTT line, T/R relay or PIN diode switching, driver and PA bias, the final, the low-pass filter relays, the forward/reflected power detector, and whatever protection logic is cutting drive. This is where it helps to ask whether there is truly no RF, or whether the rig produces RF and then folds it back. A dummy load and a power meter tell you quickly.

The workflow I'd suggest for discussion:

1. Check DC input and fuse, then each internal rail against the service manual.
2. Confirm the reference clock and PLL lock with a scope or frequency counter.
3. Test into a dummy load, never an antenna, while troubleshooting.
4. Check whether the display, CPU and band logic behave normally.
5. Only then go after the PA, protection circuits and alignment.

What do you check first? And which pieces of test gear do you consider essential rather than nice to have: a current-limited bench supply, a scope, an RF probe, a signal generator, a NanoVNA, a dummy load?

  • Replies 2
  • Views 121
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The protection circuit is worth ruling out before you condemn the finals. Many rigs reduce power when the SWR or reflected-power detector reports a mismatch. If the rig still folds back into a good dummy load, suspect the detector rather than the antenna system. Look at the bridge diodes, the trimmer or calibration pots, the op-amp or comparator stage, and any filter capacitors on the sense line. A leaky diode or a dirty trimmer can fake a high-SWR condition. Do the same check in reverse: if the rig makes full power into a deliberately bad load and doesn't protect itself, the detector may be dead, and that is how a PA gets destroyed.

If the finals really are blown, treat that as a symptom and not the whole fault. Common causes include high SWR, overdrive, supply overvoltage, bias runaway, a parasitic oscillation and a failed driver stage. Before fitting a new transistor, check the bias network for open resistors, a failed thermal-tracking device and a damaged bias preset. Look at the drive level and the output filter too. Then bring the rig up on a current-limited supply, set the idle current as the manual specifies, and watch it on a dummy load. Use the correct part or a properly matched replacement, because "close enough" RF transistors often have different gain, capacitance and ruggedness.

On alignment, it's tempting to touch the slugs when power is low or receive is deaf. Don't, until you've verified the basics. Mark the original positions, use the manual's procedure and test points, and make sure you have the right gear: a signal generator, a counter, a power meter and a dummy load. Many "misaligned" rigs turn out to have a bad component, and re-tuning around it only hides the fault.

  • Moderators

For noise and power problems, I'd separate rig noise from supply and station noise. Run the rig from a clean linear supply or a battery if you can. If the noise vanishes, look at the switching supply, the DC cabling and the grounding. If it stays, check the rig's internal rails for ripple with a scope, using a short ground spring rather than a long ground lead so you don't add pickup of your own. Excess ripple on a regulator output often points to a failing electrolytic, a regulator problem or a bad solder joint.

On capacitor replacement, a multimeter alone won't tell you much about an electrolytic. A capacitance reading helps, but ESR matters more in supply and decoupling stages, so an ESR meter is a very good addition. Don't shotgun every capacitor, though. Compare the voltage, temperature rating and ripple-current rating with the original, mind the polarity, and clean up any electrolyte residue properly. On surface-mount boards, leaked electrolyte can eat traces and pads, so inspect around the capacitor and not just the part itself. Also check for shorted tantalums on low-voltage rails.

Contact cleaning helps with intermittent faults, scratchy controls and relay-switched paths, but use it carefully. Use a cleaner suited to the component, and avoid soaking parts that can be damaged by solvents or lubricants, such as some trimmers, filters and plastic parts. After cleaning, work the control or connector repeatedly and re-test. If the fault returns quickly, look for a cracked solder joint, a worn contact or a corroded connector.

For basic gear, I'd list a DMM, a current-limited bench supply, a dummy load, an RF power meter, a scope, and the service manual or schematic. A scope makes the PLL, oscillator, ripple and keying checks far easier. An RF probe for the DMM is a cheap way to trace signal flow, and a NanoVNA helps with filters and antenna checks. For tube or older mains-powered gear, add an isolation transformer or a bulb limiter, and discharge high-voltage capacitors before working inside.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.