Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SDR gain, dynamic range and noise: where do dongles, upconverters and software settings actually matter?

ci_cover.jpg

A lot of SDR troubleshooting comes down to the same few questions. Is the receiver deaf, overloaded, or just listening to local noise? This thread is for comparing approaches across hardware (RTL-SDR, Airspy, SDRplay, HackRF, LimeSDR) and software (SDR#, SDRuno, GQRX, HDSDR, CubicSDR).

Here is a starting framework, and corrections are welcome.

Sensitivity is rarely the limit. On HF, and often on VHF in built-up areas, external noise from the antenna usually exceeds receiver noise. If connecting the antenna raises the noise floor noticeably, extra preamp gain mostly amplifies noise and strong signals together. Overload is the more common problem. Typical signs are ghost signals that move when you change gain, FM broadcast images showing up across the band, and a spectrum that gets worse as you raise the gain slider.

ADC bits are only part of the picture. Theoretical dynamic range improves by roughly 6 dB per bit, but real devices fall short of that. An 8-bit RTL-SDR has much less headroom than a 12-bit Airspy or SDRplay, and tuner linearity, AGC behavior and front-end filtering all matter too. Hardware with selectable filters (the SDRplay notches, for example) can help a lot where there is strong broadcast energy. For cheap dongles, an external FM-broadcast notch or a bandpass filter for your band of interest is often a bigger improvement than a new software package.

HF options. You can use direct sampling (supported on some RTL-SDR variants, or on HF-focused receivers), a dedicated HF-capable SDR, or an upconverter that shifts HF up into the dongle's tuning range. An upconverter adds a local oscillator, so check for spurs and phase noise, and keep its supply and cabling clean. Direct sampling on an 8-bit device is simple but limited. Aliasing and the lack of preselection are the usual complaints.

Antennas. Match the antenna to the job. A discone is a flexible wideband choice for scanning VHF/UHF. Resonant antennas such as a 1090 MHz collinear for ADS-B or a V-dipole or QFH for 137 MHz weather satellites usually beat a broadband antenna on a single task. On HF, popular choices are an end-fed wire with a 9:1 unun and a small active loop, and local noise often decides which works better. Common-mode chokes on the feedline and USB cable, a short USB lead, and keeping the dongle away from the PC all reduce self-generated interference.

Software settings. FFT size, window function and averaging change what you see on the waterfall. Frequency correction (ppm) matters most on cheap dongles without a TCXO, and it matters more at higher frequencies. For digital decoding, route audio through a virtual audio cable into tools such as WSJT-X, fldigi or DSD+. Use multimon-ng, dump1090 or rtl_433 for protocols with their own decoders. For FT8, system clock accuracy matters as much as frequency accuracy.

Panadapters and bandscopes. Feeding an SDR from a transceiver's IF output gives a wide view without a second antenna. If you instead split or tap the antenna line, make sure the SDR is protected during transmit, because many SDR front ends cannot survive transmitter power. CAT control through Omni-Rig or hamlib keeps the SDR display in sync with the radio.

What order do you usually follow when a setup misbehaves: lower gain, add filtering, change the antenna, or check the software chain?

  • Replies 2
  • Views 69
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Lowering gain first is a good habit because it costs nothing and tells you quickly what kind of problem it is. A practical test is to change the gain or attenuation by 10 dB. If the false signals change level or appear and disappear, you are looking at intermodulation or overload and not real signals. Real signals should move up and down with the gain, along with the noise floor.

For a dongle with a lot of FM broadcast energy around, a notch at 88–108 MHz is cheap and works well. If the problem is spread over a wider range, a bandpass or low-pass filter for the segment you actually want helps more. A better ADC cannot fix an overloaded front end in front of it. It only gives you more room before that point.

One caution on the "more bits is always better" argument. Gain staging still matters on 12- and 14-bit receivers, and AGC can pump on strong bursts. For weak-signal digital modes it is often better to fix the gain manually than to leave the AGC hunting.

  • Moderators

On the antenna side, test the noise before spending money. Compare the noise floor with the antenna connected and with a terminator on the input. If connecting the antenna only lifts the floor by a couple of dB at HF, the band is probably quiet and your system is receiver-limited. If it lifts it by 20 dB or more, local noise or strong signals dominate, so a quieter location or a better-placed antenna is the fix. Moving the antenna away from switching supplies, LED lighting and the PC can help more than a more sensitive receiver.

The panadapter point is also important. Splitting RF from a transmitting antenna into an SDR input without proper protection is a good way to damage a receiver. An IF tap or a dedicated receive-only path is much safer, and it is worth checking the level, because the IF output of some radios is too hot for dongles without attenuation.

For decoding, keep the signal path simple. Check the SDR software's demodulator bandwidth, then the virtual audio cable level, then the decoder's own settings. Many audio-related failures are just an overdriven or underdriven audio level between those stages, and not a problem with the radio at all.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.