Checking the bands before you call CQ: how do you combine SFI, K index, VOACAP, WSPR and beacons?
- Replies 2
- Views 120
- Created
- Last Reply
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
Propagation numbers are easy to collect and hard to turn into a decision. Solar flux, A and K, MUF maps, a VOACAP chart and a WSPR map can each say something different about the same band. I'd like to compare workflows here, and I'll start with how I think the pieces fit together.
Slow indicators (what the band is capable of). The sunspot number and the 10.7 cm solar flux (SFI) track the 11-year cycle and the Sun's ionizing output. A higher SFI generally means more ionization in the F layer, a higher MUF, and a better chance that 15m, 12m and 10m will support F2 propagation. SFI is a trend indicator, not a promise. Near solar minimum the upper bands can still open briefly, and near maximum a disturbed geomagnetic field can wreck a path.
Fast indicators (what is going wrong right now). The K index is a 3-hour measure of geomagnetic disturbance on a 0 to 9 scale. The A index is a daily value derived from it. Low, quiet numbers are good for most paths. Elevated K hurts high-latitude and transpolar paths first, with flutter, absorption and depressed MUF. Flare-driven X-ray bursts are a separate problem. They raise D-layer absorption on the sunlit side and can cause a sudden HF fadeout, no matter how good the SFI is.
Layers in plain terms. The D layer exists mainly in daylight and absorbs lower HF frequencies. Absorption falls off roughly with the square of frequency, so 160, 80 and 40m suffer most by day. That is why they come alive near and after sunset. The F layer does the long-distance refraction. If your frequency is above the MUF for the path, the signal goes through the layer instead of coming back. If it is far below the MUF, you may be paying a heavy absorption penalty. The best DX is often a little below the MUF.
Gray line. Along the day/night terminator, D-layer absorption is low at both ends, so long low-band paths can be enhanced. It helps most on 160 to 40m. The effect is real but not magic, and you still need an open path and a quiet geomagnetic field.
Predictions versus measurements. VOACAP is a prediction engine based on monthly median conditions and a smoothed sunspot number. It is good for planning, such as which band to try at what hour toward a region, but it is not a live report. WSPR, PSK Reporter, the Reverse Beacon Network and the NCDXF/IARU beacons on 14.100, 18.110, 21.150, 24.930 and 28.200 MHz tell you what is happening now. WSPR has the advantage that it works with very low power and shows real SNR numbers from real receivers. Remember that a map shows only where someone was transmitting and someone else was listening, so a blank area doesn't prove a closed path.
VHF and up. Sporadic E mostly shows up on 10m and 6m, and sometimes 2m, with a peak in late spring and summer at mid-latitudes and a smaller one in midwinter. It can appear and vanish within minutes. Tropospheric ducting comes from temperature inversions and is tied to weather, such as high pressure and stable air, or evaporation ducts over water. For tropo, a weather forecast is as useful as any solar number.
NVIS. For regional communication out to a few hundred km, you want high-angle radiation on a frequency below the critical frequency of the F layer. A low horizontal dipole on 80 or 40m is a common choice. When the critical frequency drops at night, a lower band often works better than the one that worked at noon.
So what is your order of operations? Do you check indices first and then verify with spots, or just look at WSPR/PSK Reporter and ignore the numbers? And when VOACAP and the live data disagree, which do you trust?
Link to comment
https://www.hamradiobase.com/forums/topic/10966-checking-the-bands-before-you-call-cq-how-do-you-combine-sfi-k-index-voacap-wspr-and-beacons/Share on other sites