Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a wire antenna from scratch: where do wire, choke, feedline and modeling actually matter?

ci_cover.jpg

Most homebrew antenna problems come from a few decisions made early, not from the antenna type. A resonant dipole, an inverted-V, a fed doublet and a ground-mounted vertical are all easy to build. What decides whether they work is how well the wire, supports, feedline and common-mode control are handled. Here is a baseline to argue with.

Wire and length. For a half-wave dipole, 468 divided by the frequency in MHz gives the total length in feet (143 divided by the frequency gives meters). Treat that only as a cutting length. Height, sloping ends, nearby trees and wire insulation all shift resonance, and insulated wire usually resonates a few percent lower than bare wire. Cut long, then trim for the lowest reactance at your target frequency. For permanent installs, 14 AWG hard-drawn copper or copper-clad steel resists stretching. Thinner stranded wire (18 to 20 AWG) is fine for portable use, but it sags and fatigues at the feedpoint. Wire gauge changes resistive loss very little in a dipole. It matters more for mechanical life and slightly for bandwidth.

Insulators and supports. End insulators only need to be UV-stable and stay put. Cut HDPE, acrylic or PVC will do, and ceramic works too. Rope matters more than people expect. Polyester or Dacron stays put, while nylon stretches and sags as the weather changes. At the center, let a strain-relief plate or insulator carry the load so the coax does not pull on the soldered joint. Seal the connection, because water wicking into the coax braid is a common failure.

Choke or balun. A dipole fed with coax needs something to stop common-mode current on the shield. A 1:1 current balun or a choke at the feedpoint is the usual answer. On a coax choke, the wire turns through a ferrite core matter less than the choking impedance across the bands you use. Mix 31 is commonly used for the lower HF bands, and mix 43 often suits the upper bands. Check the result by measuring the choke or by watching how much your SWR reading changes when you touch or move the coax. For ladder-line-fed antennas, a 4:1 or 1:1 balun at the tuner plus a choke on the coax after it is the typical setup.

Ladder line. A multiband doublet fed with 450 ohm window line and a tuner is simple and efficient, because feedline loss stays low even at high SWR. Keep the line away from metal, avoid sharp bends and never coil it. Choose the doublet length to avoid lengths where the feedpoint impedance reaches extreme values on your favorite bands.

Poles. Telescoping fiberglass poles make good center or end supports. Avoid carbon-fiber poles for anything near the radiator. Carbon fiber conducts and will detune or load the wire.

Measurement and modeling. SWR alone says little about efficiency. A lossy antenna can show a flat SWR. Measure resistance and reactance, preferably at the feedpoint or with a calibrated analyzer or VNA at the end of a known cable length. Then use EZNEC or MMANA-GAL to explore how sensitive your design is to height, wire diameter, ground type and end droop. MMANA-GAL has an average gain test that is a handy check on model validity. A model is a way to see trends, so confirm it with measurements.

Which part of your own builds gave you the most trouble: supports, common-mode current, trimming, or making the model match reality?

  • Replies 2
  • Views 93
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would add that traps and verticals are where model-versus-reality gaps get biggest. A trap dipole shortens overall length compared with a full-size wire, but each trap adds loss and narrows bandwidth, so the antenna is rarely as efficient as a simple full-size dipole on its fundamental band. If you want multiband without traps, a fan dipole or a linked dipole is easier to build, though spacing between the fan elements interacts and needs trimming in sequence, from the highest band down.

For verticals, the radial system matters more than the radiator. A ground-mounted quarter-wave vertical typically needs a lot of radials (a few dozen is better than a few) because ground loss dominates efficiency. Elevated radials can work with far fewer, often two to four tuned ones per band, and with the radials sloping downward the feedpoint impedance moves toward 50 ohms. A choke at the base is still worth adding, since the coax can act as an extra radial.

  • Moderators

One practical point on measuring: calibrate at the analyzer port or at the end of the cable, and know what you are measuring. If you measure through a long coax run without a choke, the shield can carry current and change the reading, so the number may drift when you move the cable or touch the analyzer. Fix that first, then trim the antenna.

In EZNEC and MMANA, two settings catch people out: segmentation and ground. Too few segments, or very different segment lengths where wires join, can give unreliable impedance. A low horizontal wire or a vertical with radials near the ground is also sensitive to the ground model. MMANA's treatment of real ground is simpler than NEC-based programs, so for low antennas compare a couple of ground assumptions, such as average and poor soil, rather than trusting one number. If the resonant frequency predicted by the model is within a few percent of what you measure, that is usually a good result. What matters is that the model predicts which way and roughly how much each trim will move the resonance.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.