Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio that carries: mic gain, ALC, compression and filter settings for weak-signal and DX work

ci_cover.jpg

Most SSB audio problems come from a few settings interacting: mic gain, processor level, ALC, EQ and transmit bandwidth. Each one can be set "by the book" and the signal can still sound bad if the others work against it. I'd like this thread to collect practical methods rather than magic numbers, because every radio, mic and room behaves differently.

Here is a framework to start from, and then I'd like to hear where people disagree.

Sideband choice. The convention is LSB below 10 MHz (160, 80 and 40 m) and USB above it (20 m through 10 m). 60 m is the usual exception, where USB is used. Using the wrong sideband won't damage anything, but nobody can copy you without switching, and in a pileup that's a good way to be ignored.

Microphone and placement. Distance and angle matter more than price. With a typical dynamic mic, a couple of inches from the lips and slightly off-axis helps avoid plosives. Get too close and the proximity effect adds boomy low end that wastes power on frequencies that don't help intelligibility. A foam windscreen costs almost nothing and helps. A hard, bare room adds reflections that compression will make worse, so a soft room or a mic closer to your mouth helps more than any menu setting.

Mic gain and ALC. ALC is a protection circuit, not a loudness control. The usual advice is to adjust mic gain so that voice peaks just touch the ALC range your manual recommends, without pushing deep into it. Heavy ALC action means the radio is clamping down on the signal, which adds distortion and widens your occupied bandwidth. If you use an external amplifier, check that its ALC line isn't also pulling your drive down, and keep the exciter clean before the amp sees it.

Processor and compression. Compression raises average power relative to peak power, which can make a signal easier to copy under noise. It also raises background noise, room sound and distortion. A modest amount of compression is the practical sweet spot for most operators. Pushing it hard can make you sound loud on the meter but fatiguing to copy. Radios differ too: some use audio-frequency compression, while others use RF clipping, which can sound harsher and spread splatter if overdriven.

EQ and bandwidth. A typical SSB transmit passband is about 2.4 to 2.7 kHz wide. Trimming low frequencies below roughly 150 to 200 Hz and adding a gentle lift in the 2 to 3 kHz range can improve clarity. A very wide transmit setting may sound nice on a quiet band but is poor etiquette when the band is crowded. Narrower isn't automatically better either, since cutting too much high end hurts consonants and intelligibility.

Monitor function. TX monitor is useful for hearing processor and EQ changes, but it doesn't tell you exactly what the other end hears. Use headphones to avoid feedback, and when possible confirm with an independent receiver, an SDR, or a recording from a station willing to give an honest report.

Questions for the thread: how do you decide how much compression is too much? What's your test method for checking your signal off the air? And when the band is busy, do you narrow your TX bandwidth or just rely on a good receive filter?

  • Replies 2
  • Views 114
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the compression question, a useful way to think about it is that the benefit is limited and the cost is cumulative. Compression doesn't create signal. It reduces the gap between your loud and quiet syllables, so the quiet parts sit higher against the noise at the far end. A few dB of compression usually helps. Beyond that, you mostly raise the noise floor of your own transmit audio, including fan noise, room echo and keyboard clatter, and intelligibility can get worse even while the signal looks stronger.

For testing, the most reliable approach is a recording from outside your shack. A remote SDR within range, or a friendly station who can record you with their radio set to a normal 2.4 kHz filter, is much more informative than an S-meter reading. Compare three versions: processor off, light processing, and your usual setting. Listen for pumping, harsh sibilance, a boxy sound and any background build-up between words.

One more thing to check is RF in the shack. If your audio gets raspy only on certain bands or at higher power, the cause may be RF getting into the mic cable or audio gear rather than any processor setting. Ferrites, better grounding and a shorter or better-shielded mic cable can fix problems no menu adjustment will.

On the bandwidth question, my view is that a clean 2.4 to 2.6 kHz signal with good low-cut is a sensible default for crowded bands. Wider settings are fine for a casual contact on a quiet frequency, provided you're not splattering and nobody is squeezed next to you.

  • Moderators

For the weak-station and DX side, receive settings matter as much as transmit audio. A 2.4 kHz filter is a good general-purpose starting point, but it isn't always the best choice. For a weak signal with QRM close by, narrowing to somewhere in the 1.8 to 2.1 kHz range can make a difference. The voice loses some fullness, but the signal can become more copyable. If your radio has IF shift or passband tuning, use it to slide the window away from an interfering signal rather than just narrowing it.

Noise reduction can help, but it needs a light touch. Aggressive NR can turn weak speech into a warbly mess and remove the cues you need to copy a callsign. The same goes for AGC: a faster setting may help when strong signals are bumping around, while a slower setting can sound smoother on steady signals. Turning down RF gain on a noisy band can also improve the readability of a weak signal by reducing the noise the AGC reacts to, though how well it works depends on your radio and conditions.

When working a DX station, much of the skill is procedural. Listen long enough to understand whether they're working split. If they are, set your transmit frequency accordingly, and never transmit on the DX's listening frequency. Keep calls short, say your callsign clearly using standard phonetics, and avoid stretching it out or repeating it endlessly. If the DX operator is working by callsign area or number ranges, wait for your turn.

For your own audio in a pileup, an overdriven signal tends to do worse than a clean one. A moderate amount of processing and well-set ALC will usually be more readable than running the maximum compression and drive. Your power is also better spent on a clean signal than on distortion products on the neighboring frequencies.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.