Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Radio mods that are worth doing (and the ones to leave alone): MARS/CAP, expanded RX, TCXO, filters, power and noise

ci_cover.jpg

Radio modification covers everything from a five-minute firmware update to opening a rig and swapping the reference oscillator. Some changes pay off a lot, some do nothing measurable, and a few can leave you with an illegal or unsafe transmitter. This thread is for comparing approaches, asking what is worth doing on a given radio, and sorting out what is legal.

Start with the goal. "Better performance" means different things on different radios. On a handheld it usually means a cleaner receiver, better audio, longer battery life, or access to a data port. On an HF rig it means improved selectivity, lower noise, and cooler finals. On a mobile it is mostly about power wiring, heat, and keeping the radio from becoming a noise source itself. Pick one measurable target first, such as frequency error, S-meter noise floor, transmit deviation, or case temperature after a set run time. Then you can tell whether the mod worked.

MARS/CAP mods. These usually mean unlocking transmit on frequencies outside the amateur bands, through a menu or software setting, a diode or jumper change, or a different firmware or channel programming. The hardware may be physically capable of it, but that does not make it legal to use. MARS and CAP operation requires membership and authorization from the relevant organization and agency. An amateur license alone does not cover those frequencies. Outside the US, the rules differ by country, so check your own regulator. The technical side also matters: a radio built for amateur bands may have filtering and a spurious-emissions profile tuned for those bands, and performance elsewhere in the range is not guaranteed. If you are authorized, verify output power and spectrum on the new frequencies with a dummy load and proper test gear. Do not assume they match the ham bands.

Expanded receive. Widening receive coverage is generally less risky than expanding transmit, but it has its own limits. Wideband front ends on handhelds and scanners are prone to overload, images, and internal spurs ("birdies"). Opening up coverage on a rig with a broad front end often reveals more of these problems than new signals. Bandpass filters, a front-end attenuator, and a decent antenna matched to the target band help more than the unlock itself. Also check local law on what you may monitor, because some jurisdictions restrict certain types of transmissions even for listening.

TCXO and frequency accuracy. Frequency error scales with frequency. At 1 ppm, the error is about 145 Hz at 145 MHz and about 440 Hz at 440 MHz. That matters for narrowband FM, repeater offsets, digital modes, and weak-signal work. A TCXO swap or reference calibration can tighten this a lot, but only if the replacement part matches the radio's reference frequency, output level, and supply voltage, and the synthesizer is set up to accept it. Calibrate against a trusted reference, such as a frequency counter with a known-good timebase, a GPS-disciplined source, or a stable known signal. If you cannot measure it, you cannot claim it improved.

Filters. For HF rigs, the most useful receive upgrades are often narrower CW/SSB filters, better roofing filters, or notch and DSP options. For VHF/UHF, cavity or helical filters, notch filters for paging or broadcast interference, and low-pass filters on the transmit side can address specific problems. Filters add insertion loss, so use them where the interference problem justifies the loss. A broadband filter that costs you 1 dB on weak-signal receive is not an upgrade if your problem was something else.

Audio upgrades. Common changes include a better speaker or speaker-mic, a new microphone element, adjusted mic gain, transmit audio EQ, or access to the discriminator and flat TX audio for 9600-baud and similar data modes. Whatever you change on the transmit side, check deviation. Overdriven audio sounds harsh, splatters, and can run over your bandwidth. On receive, a bigger or better-enclosed speaker often improves intelligibility more than any circuit change, especially on noisy mobile installs.

Firmware. Back up your configuration or memory image before updating anything. Confirm the exact model and hardware revision, because many radios look identical but differ internally. Do not interrupt an update, and use a stable power source. Third-party or modified firmware can add features but may change power limits, band limits, or emission behavior. Whoever transmits with it is responsible for compliance, so test with a dummy load first.

Cooling fans. Heat is a real limiter for mobiles and HF rigs on digital modes at high duty cycle. A fan can keep the PA within its thermal range, but it has to move air across the heatsink and not just sit near it. Cheap brushless fans can inject noise into the receiver, so run them from a filtered supply, add ferrites if needed, and watch the noise floor with the fan on and off. Do not block the radio's own vents.

Battery and power. For handhelds, swapping battery chemistry or capacity can change voltage under load, which affects TX power and low-battery cutoff behavior. Use packs with proper protection circuitry, correct charging, and a fuse where the pack feeds a radio through external wiring. For base and mobile power, voltage drop in thin or long cables is a more common cause of weak output than most people realize. Use adequately sized wire, fuse close to the source, and solid crimps. Switching supplies can be noisy on HF, so test a few options and add common-mode chokes where it helps.

RF and noise reduction. Noise reduction starts with locating the source. A portable AM radio or a handheld receiver is useful for tracing local noise. Common-mode chokes on power and data lines, better grounding and bonding, separating antennas from noisy equipment, and replacing the worst offenders (cheap chargers, LED lighting, some solar controllers) often give bigger gains than any radio mod. Ferrites are not a cure-all. The right material and enough turns for the target band matter.

Safe modding practice. Use ESD precautions, a temperature-controlled iron, and good magnification for SMD work. Photograph the board before removing anything. Change one thing at a time. Test into a dummy load with a wattmeter, then look at the spectrum for harmonics and spurs before connecting an antenna. Keep notes on stock settings so you can revert.

Legal use of modified rigs. Rules vary by country and by service. In general, you must transmit only on frequencies and modes your license or authorization allows, with emissions that meet the rules for that service. Equipment used in commercial or licensed land-mobile services typically has certification requirements, and modifying it can invalidate that certification. Amateur operators usually have more latitude to build and modify equipment, but are still responsible for clean emissions and correct operation. A radio being able to transmit somewhere does not mean you are allowed to.

Which radios are people looking at, and what do you want out of them: cleaner receive, better stability, more power headroom, or digital mode readiness? Knowing the model and the problem makes the advice a lot more specific.

  • Replies 2
  • Views 108
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Good breakdown. I'd add that the order of operations matters. Before buying a TCXO or filter, measure what you have. A cheap SDR dongle with a known reference or a frequency counter will tell you if the radio is actually off frequency. A dummy load, wattmeter, and a second receiver will tell you a lot about power, deviation, and spurs. A lot of "upgrades" are solving a problem the radio never had.

On noise, I'd put it ahead of almost every internal mod. If the S-meter is sitting at S5 from a bad wall-wart or LED driver, a new filter will not fix it. Walk the house with a battery AM radio, unplug things one at a time, and watch what changes. Then look at ferrites and grounding. It's cheap and usually gives the biggest improvement.

One caution on fans: if the noise floor rises when you power one up, it's the fan or its supply. Try a different fan, a separate filtered feed, or a small choke on the leads before blaming the radio.

  • Moderators

On the MARS/CAP point, it helps to separate three things: what the hardware can do, what the software lets you do, and what you are authorized to do. A menu unlock or jumper only changes the second. Without membership and authorization in the relevant program, using those frequencies is not covered by an amateur license, and the rules differ again outside the US.

Even for authorized use, check that the radio's specs are valid where you are operating. Output power, filtering, and spurious emissions may not be characterized outside the ham bands, so test it instead of assuming. Also keep in mind that if a modified radio is used in a service that needs certified equipment, the modification itself can be the problem.

For firmware, I'd avoid flashing anything unless you can identify the exact hardware revision and have a way to restore the original. Wrong-variant flashes are a common way to turn a good handheld into a brick. If a build changes band limits or power tables, treat it as a different radio and re-verify it on a dummy load before putting it on the air.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.