Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 48-hour field comms shelter: LiFePO4 vs generator, noise control, and what belongs on the checklist

ci_cover.jpg

I'm putting together a standard deployment kit for a served-agency style shelter station, and I'd like the setup picked apart before it gets locked in. The target is a tent or pop-up with one HF position (100 W class rig), one VHF/UHF dual-band mobile for local nets and repeater or simplex work, a laptop for logging and digital modes, a few LED lights, and phone and radio chargers. The deployment could last 24 to 48 hours with no grid power and operators rotating in and out.

The current plan is a roughly 100 Ah LiFePO4 battery as the primary supply, with a small inverter generator as backup for recharging only. A 200 W folding solar panel with an MPPT controller would top it up when conditions allow. Distribution would be a fused DC panel with Anderson Powerpole outputs. For antennas, the plan is a fiberglass telescoping mast carrying an end-fed half-wave or inverted-V for HF, plus a separate J-pole or small vertical on its own mast for VHF/UHF. Coax would be about 50 ft to the HF antenna and 30 to 50 ft to the VHF antenna.

The questions I'm trying to settle: how should I size the battery honestly, should the generator ever run while we are transmitting on HF, what is the sensible way to handle grounding in a field setup, and what do people most often forget on teardown? If you spot something wrong in the basic layout, say so. I'd rather find the weak points on paper.

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the power budget, because everything else follows from it. A 100 Ah LiFePO4 battery is about 1,280 Wh nominal. Usable energy is somewhat less once you account for inverter losses (if you use one), cable drop, and a reserve you don't want to cross. Treat roughly 1,000 Wh as a planning number and adjust from there.

Then look at your rig's spec sheet instead of guessing. A 100 W HF transceiver can draw around 20 A on key-down at full power, but SSB voice and typical net traffic average far lower. Receive current is usually 1 to 2 A, and a laptop, lights and chargers add to that. Build a table with a receive load, a transmit load and an assumed duty cycle, then add a safety margin. Digital modes at high duty cycle change the picture a lot, so run FT8-style or Winlink sessions at reduced power if you can. Many stations only need 25 to 50 W for regional work.

On solar, a 200 W panel rarely delivers 200 W. Angle, temperature, haze, shade from tents and trees, and season all cut it down. It's good for offsetting the draw during the day, but I wouldn't count it as your only recharge plan for a 48-hour deployment. Keep the controller away from your HF antenna and receiver, and put ferrites on the panel lead and the load lead. Some MPPT controllers are noisy on HF, so test yours before the deployment, not at the site.

For LiFePO4 in general: fuse close to the battery positive terminal, size the wire for the fuse rather than the other way around, and avoid undersized Powerpole crimps. Check the BMS specs, since many cells shouldn't be charged below freezing unless the battery has low-temperature protection or heating. A fully charged LiFePO4 can sit near 13.4 to 13.6 V under light load and sag toward 12.8 V as it discharges, so confirm your gear is happy across that range and that your charger or solar controller has a proper LiFePO4 profile.

On the generator: using it only for recharging is a sensible approach. An inverter generator is quieter than a conventional unit, but its output can still produce RFI from the engine ignition and the inverter electronics, and the noise from the charger or power supply you plug into it can be worse. The safest pattern is to run the generator some distance away, charge the battery, then shut it off during critical HF operating. If the generator must stay on, keep it downwind and well away from the shelter, put a CO alarm in the tent, never run it inside or near openings, and use a GFCI-protected cord. Let it cool before refueling, and store fuel away from the operating area. If you backfeed or tie into a building circuit, do it only through a properly installed transfer arrangement, never with a male-to-male cord.

One more noise point: switching supplies and cheap USB chargers are some of the biggest field noise sources. Keep an identical 'quiet' test: with the battery alone, note the HF noise floor, then add one device at a time and watch the S-meter or waterfall.

  • Moderators

Antennas, coax and grounding, since that's the other half of this.

The mast: a fiberglass telescoping pole is fine for an inverted-V or EFHW if you guy it properly. Use at least three guy points at the upper section and the base, with stakes or weights sized to the wind forecast and the soil. Ballast like water jugs or sandbags helps on pavement. Don't raise a mast anywhere it could fall into power lines, and treat that as a hard rule. Keep the guy lines marked so people don't trip on them, and keep the antenna away from where the public or volunteers walk. For your end-fed, give some thought to the transformer's power rating and to the counterpoise or coax shield acting as part of the antenna. A common-mode choke at the feedpoint and another near the shack can reduce RF on the coax and the noise coming down it.

Coax loss matters most on VHF/UHF. Thin RG-58 style cable can eat a lot of power at 146 or 440 MHz over a 50 ft run, so check the manufacturer's loss tables and consider a lower-loss cable like an LMR-400 type for that run. HF at these lengths is far more forgiving, so use thinner cable there if weight matters. Whatever you use, make connectors weatherproof and keep coax from lying in water, and put a drip loop where it enters the tent. Run coax away from power cords where you can, and cross them at right angles rather than in parallel.

Grounding is where field operators often have mixed ideas. A ground rod at a temporary site will not protect you from a lightning strike. The safety plan for thunderstorms is to stop operating, disconnect antennas and stay away from masts, and shelter appropriately. What bonding does give you is a common reference: tie equipment chassis together with a short, heavy bond, keep DC negative and equipment grounds consistent, and follow the generator's manual for its neutral-ground configuration. An RF ground at HF is often more about choosing the right antenna and choke than about driving rods. If you see RF in the mic or the logging computer, the fix is usually a choke, ferrite, shorter cable runs, or antenna placement, not just another rod.

For the shelter, weight the tent or canopy for wind from the start, keep sidewalls available, and put the power and antenna entries on the leeward side. Use cable covers or flags in walkways. Lighting should be low glare and low noise, and red or dimmable lights help when someone is working a radio at night. Keep a paper log and spare pens even if you log on the laptop.

Checklists I'd build in: a pre-departure list (batteries charged, fuses, spare Powerpoles and crimper, adapters, spare coax jumpers, chokes, tools, printed frequency plan and net info, forms, and ID), a setup order (site survey, shelter, power, antennas, feedline, radios, then a noise and SWR check before you declare ready), an operating list (check-in times, operator rotation, battery voltage log, fuel log), and a teardown list in reverse. On teardown, count the stakes and guy lines, coil coax loosely, recover all small hardware, label any damaged items for repair, and recharge and inspect the batteries before storage. The usual misses are tent stakes, cable ties, a missing short jumper, and a half-charged battery that gets stored that way.

For EMCOMM use specifically, write down the communications plan before you leave: who you serve, primary and alternate frequencies, net control, message format, and when you report status. A well-powered station with a vague plan is less useful than a modest station with a clear one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.