Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Choosing a VHF/UHF antenna: J-pole vs slim jim vs 5/8 whip vs yagi, and where installs usually go wrong

ci_cover.jpg

This thread is for comparing common 2 m / 70 cm antenna options on practical terms: pattern, gain, mounting, feedline and connectors. Many choices get made on advertised gain figures, but the install often matters more than the antenna design. Below is a rough framework. Correct it, add numbers, and say where it doesn't hold.

Quarter-wave whip. At 146 MHz a quarter-wave is roughly 19 to 20 inches, and at 446 MHz roughly 6.5 inches. It is a monopole, so it depends on a ground plane. A car roof works well because it is a large, flat conductor under the element. Gain is modest, and the pattern is omnidirectional in azimuth with a fairly low takeoff angle when mounted on a good ground plane. It is mechanically simple, tolerant of imperfect installs, and often gives a decent match with little tuning.

5/8 wave. A 5/8-wave vertical has a base matching coil and is usually quoted as having a couple of dB more gain than a quarter-wave in ideal conditions. The extra gain comes from a flatter vertical pattern, with more energy toward the horizon. It still depends on the ground plane, and a small or off-center ground plane can distort the pattern and move the SWR. On a vehicle, a 5/8 on a roof center mount is a sensible choice. On a small metal plate, a quarter-wave may behave better than expected.

J-pole and slim jim. Both are end-fed half-wave designs with a matching section, so they don't need a ground plane the way a quarter-wave does. The weak point is the feedline. If the coax shield isn't isolated, it becomes part of the radiating system and the pattern gets skewed. A few turns of coax as a choke, or ferrite beads, near the feedpoint often improves behavior. A slim jim is essentially a folded J-pole variant. It is often said to give a slightly lower takeoff angle, but the gain should still be treated as roughly dipole-class, not magic. Construction accuracy matters, as does keeping the antenna away from metal masts and gutters.

Collinears. Stacking phased elements squeezes the vertical pattern, which raises gain at the horizon. The tradeoff is vertical beamwidth. A high-gain collinear on a tilted mast, or used where the other station is far above or below you (steep hills, tall buildings), can underperform a lower-gain antenna. Also check how a manufacturer states gain: dBi and dBd differ by about 2.15 dB.

Yagis. A directional antenna adds gain and also rejects signals from other directions, which can help a lot against interference or when working a distant repeater. It needs aiming and a rotator or manual pointing. Polarization must match the intended use: vertical for typical FM repeaters and simplex, horizontal for most weak-signal SSB/CW work.

Coax and connectors. Loss rises quickly with frequency. As approximate figures, small coax such as RG-58 can lose several dB per 100 ft at 146 MHz and noticeably more at 446 MHz. Low-loss types such as LMR-400-class cable lose much less. Check the manufacturer datasheet for the cable you are actually buying. PL-259/SO-239 (UHF) connectors are fine for many VHF runs, but they aren't constant-impedance and are usually avoided at higher UHF frequencies. N-type is constant-impedance, better sealed when installed properly, and the better choice for outdoor 70 cm and up. Weatherproofing matters for either one: water in a coax connector can ruin a good antenna.

Mag mounts and NMO. A magnetic mount is quick and removable, but it needs a clean, flat metal surface, and the coax routing through a door or window seal can be fragile. An NMO mount needs a 3/4 inch hole, but it gives a solid, low-profile, repeatable installation and a proper ground connection. Whichever you use, the roof center is usually the best location.

SWR. A low SWR isn't the same as an efficient antenna. A dummy load is an excellent 1:1 SWR. Lossy coax can also make a bad antenna look better at the radio end, because the reflected power is attenuated on its way back. Measuring at the antenna end with an analyzer is more informative than reading the radio's meter. SWR 2:1 corresponds to about 0.5 dB of mismatch loss, which is less dramatic than many people assume, but with long coax runs at UHF it adds to the existing cable loss.

Polarization and satellites. Cross-polarization between vertical and horizontal antennas can cost on the order of 10 to 20+ dB in practice. That is why handheld use with a tilted radio sounds worse than a roof-mounted vertical. For FM satellites, signals rotate and fade, so circular polarization (crossed yagis, turnstile/eggbeater types) is common for fixed stations. Portable operators often use a handheld two-band yagi and accept some polarization fading. Doppler shift also matters: the downlink frequency drifts during a pass and you retune.

Questions to get the thread going: What are you trying to reach (local repeater, distant repeater, simplex, satellites)? Is the antenna on a vehicle, a mast, or a balcony? Which feedline run are you planning, and at which band do you care most about loss?

  • Replies 2
  • Views 50
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One thing to add is that if the goal is a fixed station for repeater access, work out the path first and the antenna second. If the repeater is within line-of-sight and decently strong, a plain vertical is usually enough, and the coax and connector quality will have more effect than 2 dB of extra antenna gain. If the repeater is marginal, a small vertically polarized yagi aimed at it can turn a noisy signal into a quiet one, and it will often reduce interference from other directions too. The tradeoff is that you have to aim it, and if the repeater's coverage is wide and you only occasionally use another one, you may regret the narrower beam.

On J-poles specifically: the feedline question is the one most builds skip. If the pattern looks lopsided or the SWR shifts when you touch or move the coax, the shield is probably carrying current. A choke near the feedpoint is cheap to add and easy to test.

  • Moderators

For mobile, the usual practical order is: location of the mount first, then cable routing, then antenna type. A roof-center NMO with a quarter-wave or 5/8 whip is a sensible baseline. A trunk-lip or fender mount makes the pattern lopsided, because the metal around the antenna isn't symmetrical. Magnets are fine for temporary use but check the paint and keep the surface clean, and use a short, round coax path rather than flat cable pinched in a door. Whatever you choose, check the SWR across the band you use, not just at one frequency, because mounting position changes the resonance. A 5/8 whip also isn't guaranteed to beat a quarter-wave in real life if the ground plane is poor.

On connectors: PL-259 is acceptable for a mobile VHF setup with a short run, but if you also run UHF or the connection will be outside and exposed, N-type with proper sealing is a better long-term choice. The more frequently you swap antennas, the more a repeatable, well-made connection matters, because a half-soldered center pin looks like an antenna problem when it is really a connector fault.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.