ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Small-yard HF antenna choices: what SWR hides, and where the losses actually are
Planning an HF antenna for a lot where the options are one tall support, a couple of trees, and a rule against anything that looks like an antenna? The usual shortlist is an end-fed half-wave (EFHW), an off-center fed dipole (OCFD), a G5RV, a doublet on ladder line, an inverted V, a trap dipole, a loop, or a vertical. They all work to some degree. Which is best depends on where the losses land and what the pattern does, and the SWR meter tells you very little about either.
Here is a framework for comparing them, with the common misconceptions flagged.
SWR measures the match at one point, not efficiency. A dummy load gives a perfect 1:1 and radiates nothing. An antenna with a lossy transformer, poor radials, or a high-loss feedline can also show a low SWR. The reverse is also true: a well-built doublet on ladder line can show a very high SWR at the antenna and still radiate well, because balanced line has low loss even when mismatched. When someone says an antenna is good because it's 1.2:1, ask where they measured it and what sits between the meter and the radiator.
Coax loss is the clearest example. Coax loss rises with frequency and rises further when SWR is high. A short run of RG-213 at 7 or 14 MHz loses very little when matched, but thin coax such as RG-58 on a long run at 28 MHz with a high load SWR can waste a surprising share of your power. Check the manufacturer's matched-loss figures and then add the mismatch penalty. For non-resonant antennas fed with coax and a tuner at the radio, keep the coax short or use ladder line to the point where the tuner is.
The EFHW is attractive because it needs only a single wire and a transformer. The feedpoint of a half-wave wire is very high impedance, often a few thousand ohms, so a 49:1 or 64:1 impedance transformer (around a 7:1 or 8:1 turns ratio) brings it down near 50 ohms. A wire cut for 40 m usually also works on 20, 15, and 10 m, since those bands sit near harmonics of the fundamental. It will not work on 30 m, which is not a harmonic of 40 m. The weak points are the transformer core (heating at high power or high SWR), the lack of a real counterpoise, and the fact that the outside of the coax often becomes part of the antenna. A common-mode choke on the coax a short distance from the transformer is cheap insurance, and so is keeping the high-voltage wire end away from people and flammable surfaces.
The OCFD, or Windom-style antenna, feeds the wire about a third of the way along its length, usually through a 4:1 or 6:1 current balun. It also works on harmonically related bands, and the impedance is generally easier on the balun than an EFHW's. The tradeoffs are that the radiation pattern becomes lobed on the higher bands, the SWR on bands not in the design set can be awkward, and the balun needs a real choking impedance as well as the transformation, or the coax will radiate.
The G5RV is a 102 ft (about 31 m) dipole with a roughly 34 ft (10.4 m) section of ladder line that then connects to coax. It was designed with 20 m in mind, where it behaves as a three-half-wave antenna. On other bands it is simply a dipole with a matching section of unknown impedance, so expect to use a tuner. That works, but it doesn't make the G5RV a magic multiband antenna. A choke where the ladder line meets the coax helps, and so does keeping the ladder line away from metal and running it vertically for a while before bending it.
A doublet is the same idea made more flexible: a center-fed wire of whatever length fits, fed with low-loss open-wire or window line and matched with a balanced tuner (or a tuner plus a good 4:1 or 1:1 balun). The feedpoint impedance varies a lot with band, and some lengths are unfortunate on some bands, so check a modeling program before cutting wire. Its big advantage is low loss: ladder line tolerates high SWR much better than coax. The disadvantage is that you have to bring ladder line into the shack, away from metal and other conductors.
A dipole's height changes its pattern more than most people expect. A 40 m horizontal dipole at around a quarter wavelength (roughly 10 m or 33 ft) has strong high-angle radiation, which is great for regional contacts but not for DX. At half a wavelength, more energy goes out at low angles. An inverted V with the apex high and the ends lower also tends to be a little less directional and a little shorter in resonant length than a flat-top, and it often has an impedance closer to 50 ohms when the included angle is wide enough. Keep the ends out of reach, since they carry high voltage.
Trap dipoles let you cover several bands on a single wire, but each trap has loss, narrows the bandwidth, and shortens the physical length. They are mechanically simple but electrically a compromise. For some small yards, a trap dipole or a fan dipole (parallel wires for different bands) is the easiest installation, as long as you keep the wires from interacting too strongly.
Verticals are very different. A quarter-wave vertical with a few elevated, tuned radials can be a decent low-angle DX antenna. A ground-mounted one needs many radials, because each radial reduces ground loss and improves efficiency. A short loaded vertical makes this worse: the shorter it is, the lower the radiation resistance and the more any loss resistance matters. A vertical that tunes easily with a handful of radials can still be a poor radiator compared with a dipole that is simply up in the air.
Magnetic loops are the classic answer when height and space are limited. A small loop can be well-behaved, quiet on receive, and surprisingly effective, but efficiency depends heavily on conductor size, the quality of the capacitor and its connections, and the loop's size relative to the wavelength. They are narrow, so you retune when you move across a band. The tuning capacitor can have very high voltage across it at higher power, so safe spacing matters.
A Yagi gives real gain and front-to-back ratio, but needs a rotator, a tower or mast, and a lot of mechanical support. A compact three-element design on 20 m can add several dB over a dipole in its main lobe and reject signals from behind. For HOA settings, that tower is usually the problem rather than the electrical design.
For a stealth setup, a thin wire between trees or along a roof edge, an attic dipole, or a vertical disguised as a flagpole are the usual options. Attic antennas work but are subject to loss from nearby wiring, insulation, and roofing, and you need to watch RF exposure for the people living there. For any antenna near people, calculate the exposure at your power level rather than guessing.
What does the group suggest for a lot with one 30 ft support and two trees at about 40 ft? And how do you decide between a lossy-but-simple match (an EFHW or a vertical) and a more complex but efficient design (a doublet on ladder line)?
Planning an HF antenna for a lot where the options are one tall support, a couple of trees, and a rule against anything that looks like an antenna? The usual shortlist is an end-fed half-wave (EFHW), an off-center fed dipole (OCFD), a G5RV, a doublet on ladder line, an inverted V, a trap dipole, a loop, or a vertical. They all work to some degree. Which is best depends on where the losses land and what the pattern does, and the SWR meter tells you very little about either.
Here is a framework for comparing them, with the common misconceptions flagged.
SWR measures the match at one point, not efficiency. A dummy load gives a perfect 1:1 and radiates nothing. An antenna with a lossy transformer, poor radials, or a high-loss feedline can also show a low SWR. The reverse is also true: a well-built doublet on ladder line can show a very high SWR at the antenna and still radiate well, because balanced line has low loss even when mismatched. When someone says an antenna is good because it's 1.2:1, ask where they measured it and what sits between the meter and the radiator.
Coax loss is the clearest example. Coax loss rises with frequency and rises further when SWR is high. A short run of RG-213 at 7 or 14 MHz loses very little when matched, but thin coax such as RG-58 on a long run at 28 MHz with a high load SWR can waste a surprising share of your power. Check the manufacturer's matched-loss figures and then add the mismatch penalty. For non-resonant antennas fed with coax and a tuner at the radio, keep the coax short or use ladder line to the point where the tuner is.
The EFHW is attractive because it needs only a single wire and a transformer. The feedpoint of a half-wave wire is very high impedance, often a few thousand ohms, so a 49:1 or 64:1 impedance transformer (around a 7:1 or 8:1 turns ratio) brings it down near 50 ohms. A wire cut for 40 m usually also works on 20, 15, and 10 m, since those bands sit near harmonics of the fundamental. It will not work on 30 m, which is not a harmonic of 40 m. The weak points are the transformer core (heating at high power or high SWR), the lack of a real counterpoise, and the fact that the outside of the coax often becomes part of the antenna. A common-mode choke on the coax a short distance from the transformer is cheap insurance, and so is keeping the high-voltage wire end away from people and flammable surfaces.
The OCFD, or Windom-style antenna, feeds the wire about a third of the way along its length, usually through a 4:1 or 6:1 current balun. It also works on harmonically related bands, and the impedance is generally easier on the balun than an EFHW's. The tradeoffs are that the radiation pattern becomes lobed on the higher bands, the SWR on bands not in the design set can be awkward, and the balun needs a real choking impedance as well as the transformation, or the coax will radiate.
The G5RV is a 102 ft (about 31 m) dipole with a roughly 34 ft (10.4 m) section of ladder line that then connects to coax. It was designed with 20 m in mind, where it behaves as a three-half-wave antenna. On other bands it is simply a dipole with a matching section of unknown impedance, so expect to use a tuner. That works, but it doesn't make the G5RV a magic multiband antenna. A choke where the ladder line meets the coax helps, and so does keeping the ladder line away from metal and running it vertically for a while before bending it.
A doublet is the same idea made more flexible: a center-fed wire of whatever length fits, fed with low-loss open-wire or window line and matched with a balanced tuner (or a tuner plus a good 4:1 or 1:1 balun). The feedpoint impedance varies a lot with band, and some lengths are unfortunate on some bands, so check a modeling program before cutting wire. Its big advantage is low loss: ladder line tolerates high SWR much better than coax. The disadvantage is that you have to bring ladder line into the shack, away from metal and other conductors.
A dipole's height changes its pattern more than most people expect. A 40 m horizontal dipole at around a quarter wavelength (roughly 10 m or 33 ft) has strong high-angle radiation, which is great for regional contacts but not for DX. At half a wavelength, more energy goes out at low angles. An inverted V with the apex high and the ends lower also tends to be a little less directional and a little shorter in resonant length than a flat-top, and it often has an impedance closer to 50 ohms when the included angle is wide enough. Keep the ends out of reach, since they carry high voltage.
Trap dipoles let you cover several bands on a single wire, but each trap has loss, narrows the bandwidth, and shortens the physical length. They are mechanically simple but electrically a compromise. For some small yards, a trap dipole or a fan dipole (parallel wires for different bands) is the easiest installation, as long as you keep the wires from interacting too strongly.
Verticals are very different. A quarter-wave vertical with a few elevated, tuned radials can be a decent low-angle DX antenna. A ground-mounted one needs many radials, because each radial reduces ground loss and improves efficiency. A short loaded vertical makes this worse: the shorter it is, the lower the radiation resistance and the more any loss resistance matters. A vertical that tunes easily with a handful of radials can still be a poor radiator compared with a dipole that is simply up in the air.
Magnetic loops are the classic answer when height and space are limited. A small loop can be well-behaved, quiet on receive, and surprisingly effective, but efficiency depends heavily on conductor size, the quality of the capacitor and its connections, and the loop's size relative to the wavelength. They are narrow, so you retune when you move across a band. The tuning capacitor can have very high voltage across it at higher power, so safe spacing matters.
A Yagi gives real gain and front-to-back ratio, but needs a rotator, a tower or mast, and a lot of mechanical support. A compact three-element design on 20 m can add several dB over a dipole in its main lobe and reject signals from behind. For HOA settings, that tower is usually the problem rather than the electrical design.
For a stealth setup, a thin wire between trees or along a roof edge, an attic dipole, or a vertical disguised as a flagpole are the usual options. Attic antennas work but are subject to loss from nearby wiring, insulation, and roofing, and you need to watch RF exposure for the people living there. For any antenna near people, calculate the exposure at your power level rather than guessing.
What does the group suggest for a lot with one 30 ft support and two trees at about 40 ft? And how do you decide between a lossy-but-simple match (an EFHW or a vertical) and a more complex but efficient design (a doublet on ladder line)?
Link to comment
https://www.hamradiobase.com/forums/topic/10998-small-yard-hf-antenna-choices-what-swr-hides-and-where-the-losses-actually-are/Share on other sites