Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning an HF shack around a 100 W rig: power, bonding, tuner placement, and when filters matter

ci_cover.jpg

This is a thread for the unglamorous parts of an HF station that usually decide how it behaves day to day. Whether the main radio is an IC-7300, IC-7610, FT-991A, FTDX10, TS-590SG, TS-890S or K3S, with a KX3 or G90 as the portable or backup rig, the same few questions keep coming up. Where should the tuner go? Is a band-pass filter worth buying? How should the station be grounded and bonded? Why does the receiver get noisy only when the amp or the computer is on?

Power supply. A 100 W transceiver typically needs 20 A or more at 13.8 V on transmit, so the supply's headline rating is only part of the picture. Check that it holds voltage under load (some switching supplies sag or trip on SSB peaks), that it does not put RFI into the receiver, and that the DC cable is short and heavy enough to keep voltage drop low. Fuse the positive lead close to the supply, and use the radio's own fused cable where one is supplied. If you run several accessories, a fused distribution block with proper connectors is tidier and safer than daisy-chained lugs. If a switching supply makes the noise floor jump, try ferrites on the DC leads and moving the supply away from the receive antenna feedline before you blame the radio.

Bonding versus 'RF ground'. It helps to separate three jobs:

  • Safety. Equipment chassis connect to the mains safety earth.
  • Lightning protection. Coax and rotor/control cables go through an entry panel with arrestors, bonded to a ground system that is itself bonded to the electrical service ground, following local code.
  • RF behavior. This is where people expect a ground rod to fix RF in the shack, but most RF-in-the-shack problems are common-mode current on feedlines and cables, not a missing earth connection.

A short, wide bonding strap between the radio, amp, tuner and power supply, plus common-mode chokes on the coax at the feedpoint and where it enters the shack, will usually do more for RFI than another ground rod. Separate ground rods that are not bonded to each other can create a potential difference during a lightning event, which is why bonding them is the usual advice.

Tuner placement. A tuner at the radio makes the rig see a load it can drive, but it does not make the antenna system more efficient. With a mismatched antenna on coax, SWR at the antenna end can still be high, and loss in the line grows with it. A tuner at the feedpoint avoids that, and is why remote tuners are popular with end-fed and random-wire systems. With an amplifier, the usual order is rig, amp, then tuner, so the amp sees a proper load. Many radios have built-in tuners with a limited matching range, and the G90's and KX3's internal tuners are useful for portable work but are not magic on every random length of wire.

Band-pass filters. Do you need them? It depends on the receiver front end and the environment. Modern direct-sampling and hybrid radios rely on a mix of front-end filtering, attenuators, preamps and sometimes preselectors, and overload behaves differently from traditional superhets. Filters become much more relevant if you have a strong local signal (broadcast, another amateur, a nearby transmitter), run multiple transmitters on different bands in the same location, or are working a contest-style multi-op setup. For a single-operator station with one radio, adding BPFs won't help with noise from a power supply or a bad neighbor's LED lighting, so try the attenuator and preamp settings first.

Layout. Keep the RF runs short, separate the coax from the AC and USB cables where possible, and keep the keyboard, monitor and any PC power bricks away from the receive path. USB audio and CAT cables are a common source of hum and hash, so ferrites at both ends and a clean grounding scheme are worth the effort. If you use a computer for digital modes, a USB isolator or a purpose-built interface can cure ground-loop hum.

Which of these has been hardest to get right in your own setup? And if you were building from scratch with a mid-range budget, would you spend on a better receiver, a good power supply, or the station ground and antenna system first?

  • Replies 2
  • Views 57
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the 'antenna system first' question, I'd put the antenna and feedline ahead of any radio upgrade. A rig with a better dynamic range figure can't recover signal you never captured, and a 100 W radio into a poor antenna is a 100 W heater for the coax. That said, the order of spending does depend on what is actually limiting the station. If the noise floor is high and you can't hear weak signals, the fix may be locating or filtering the local noise source, not buying a new receiver.

A point about the tuner: it's worth separating 'the radio is happy' from 'the system is efficient'. An ATU that shows 1:1 at the rig can be hiding a very high SWR on the line. With a short run of good coax on a moderate mismatch, the extra loss is small. On a high-SWR multiband wire with long thin coax, it can become significant. Open-wire or ladder line with a balanced tuner is often better for that kind of antenna, and the choke at the transition matters.

  • Moderators

I'd add a note on bonding and amplifiers, since the thread covers both. When you add an amp, the chassis bonding and the RF return path matter more because higher power makes any common-mode problem more obvious. Symptoms such as a tingle on the microphone, erratic SWR readings, or the radio's display glitching on transmit generally mean RF is on the shield or the control cables. Chokes on the coax, the amp keying line, and the USB or CAT cable are the first things to look at.

On band-pass filters, there's a difference between using them on the receive path and in-line on the transmit path. A BPF rated for transmit power sits between the radio and the amp, or after the amp, and has to handle the power and the SWR. A receive-only preselector is a separate device with different ratings. It is worth checking the manufacturer's specified power handling, insertion loss on the band you care about, and what happens to the filter when the SWR is poor. A filter that is fine at 100 W into a 1:1 load may not be fine into a mismatch. What bands and antennas are people planning to use? That will change the advice quite a bit.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.