Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Band plan vs. FCC rules: how do you work out where to operate from 160 m to 33 cm, and where the band edges really are?

ci_cover.jpg

I'd like to get a clear mental model of how band plans, license privileges and frequency allocations fit together. The charts I've seen (FCC privilege tables, the ARRL band plan, local repeater directories) seem to answer slightly different questions, and it's easy to mix them up. Here are the specific things I'd like sorted out:

1) What is legally required and what is just a gentleman's agreement? 2) How do you read the CW, digital and phone segments on 160 through 10 meters, and where do the privileges for Technician, General and Extra actually differ? 3) How should you handle band edges, especially with LSB and USB and with digital modes where the dial frequency isn't where the signal sits? 4) What are the sensible places to operate and call on 6 m, 2 m, 70 cm and 33 cm? 5) How do 60 meters and the international differences work?

This is a US-centric question, but I'd welcome notes on other ITU regions. Please say if something should be verified against the current rules rather than trusted from memory.

  • Replies 2
  • Views 48
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the split between law and convention. The FCC rules in Part 97 are the law: which bands your license class can use, which emission types are allowed in which segments, power limits, and so on. The ARRL band plan is voluntary. It says where the community has agreed to put SSB, narrowband digital, beacons, SSTV, calling frequencies and so on. You can be perfectly legal and still be a nuisance if you park a wide signal in the middle of the weak-signal segment, and you can follow the band plan and still be illegal if you're outside your privileges.

On HF, think in three layers. The bottom of each band is CW and narrowband data. Phone sits in the upper part. Inside the CW/data area, the digital modes tend to cluster at conventional spots. The popular FT8 dial frequencies are roughly 1.840 on 160 m, 3.573 on 80, 7.074 on 40, 10.136 on 30, 14.074 on 20, 18.100 on 17, 21.074 on 15, 24.915 on 12 and 28.074 on 10. These are conventions, not rules, and they shift a little between sources, so cross-check with the software's own list or the current band plan.

For privileges, the big picture is this. Technicians get limited HF: CW on segments of 80, 40 and 15 m, and on 10 m CW and data from 28.000 to 28.300 plus CW and SSB from 28.300 to 28.500, with a 200 W PEP limit. Generals get all the amateur HF bands, but not all the segments. The Extra-only slices sit at the low end of the 80, 40, 20 and 15 m phone and CW areas, so General phone starts around 3.800, 7.175, 14.225 and 21.275. Extras get everything. Always read the exact edges from the FCC table, because the numbers above are the ones people commonly remember.

The special cases are worth memorizing. 30 m is CW and data only, with a 200 W PEP limit, and no phone. The 30, 17 and 12 m bands are the WARC bands, so by convention there are no contests there. On 20 m, the NCDXF/IARU beacons transmit around 14.100, with similar beacon spots near 18.110, 21.150, 24.930 and 28.200. Don't transmit right on top of those.

Band edges are where sidebands bite. The rule is that your whole occupied bandwidth has to be inside your privileges, not just the dial reading. On LSB the signal extends below the dial frequency. If your General phone segment starts at 3.800 and you sit at 3.800 LSB, the lower part of your signal is outside the segment. Back off by the width of your signal plus some margin. On USB it's the reverse: at the top of the band or at the top of your privilege segment, you need that margin above the dial. With digital modes, the signal sits at dial frequency plus the audio offset, so something at a 2.5 kHz audio tone is actually 2.5 kHz above the dial, and the same margin logic applies. When in doubt, move away from the edge by a couple of kilohertz rather than test how well your radio's filter and your math agree.

Finally, 160 m is shared in a way that matters for etiquette. CW and narrow digital are conventionally at the bottom, and phone and wider modes are higher. If you listen for a minute, you'll learn where people actually sit.

  • Moderators

I'll take the VHF/UHF side, plus 60 m and the international bit. Same caveat as above: check the current Part 97 text and the band plan, because I'm giving the commonly used frequencies, not an authoritative table.

6 m (50-54 MHz): this is the "magic band" with a clear weak-signal section at the bottom. CW and beacons live around the lowest 100 kHz. SSB weak-signal activity follows, with 50.125 as the SSB calling frequency and the intercontinental DX window around 50.100 to 50.130. The common FT8 frequency is 50.313. The national FM simplex calling frequency is 52.525. Technician and above all have full privileges on 6 m, so class isn't the limit here.

2 m (144-148 MHz): 146.520 is the national FM simplex calling frequency. It's a calling frequency, not a hangout, so make contact and then move to another simplex channel. Other widely used simplex spots are around 146.40 to 146.60 and 147.42 to 147.57. Typical repeater outputs run roughly 146.61 to 146.97 with a negative offset, and 147.00 to 147.39 with a positive offset, usually 600 kHz, though local coordination decides what's really used. Weak-signal SSB and CW are at the bottom of the band, and 144.200 is the usual SSB calling spot. APRS in North America is on 144.390.

70 cm (420-450 MHz in the US): 446.000 is the national FM simplex calling frequency. SSB and CW weak-signal work is around 432, with 432.100 as the calling frequency. Repeaters commonly use a 5 MHz offset, and the exact sub-bands depend on your region's frequency coordination. There are geographic restrictions on parts of 70 cm because of other services, so check the footnotes in Part 97 for your area.

33 cm (902-928 MHz): this is the awkward one. It's allocated to amateurs only in ITU Region 2, and it's shared with other users, including unlicensed Part 15 devices, so noise and interference are common. 902.1 is often used as a weak-signal calling frequency, and FM simplex and repeater use is up to local plans, so look at what your area coordinator publishes.

60 m is channelized in the US rather than a continuous band. As I understand it, there are five channels, and General class and above can use them. Voice goes out on USB. The channel center frequencies are 5332, 5348, 5358.5, 5373 and 5405 kHz, which correspond to USB dial settings of 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5 kHz. The power limit is 100 W PEP ERP relative to a half-wave dipole, the bandwidth limit is 2.8 kHz, and CW and some digital modes are also allowed on the channels. We share it with other users, so I'd double-check the current rule text.

Internationally, the 'ITU Region' idea matters. Region 1 covers Europe, Africa and the Middle East, Region 2 the Americas, and Region 3 most of Asia and the Pacific. For example, 40 m is 7.000 to 7.200 in Regions 1 and 3 and 7.000 to 7.300 in Region 2. 80 m is 3.5 to 3.8 in Region 1 and 3.5 to 4.0 in Region 2, and 2 m is 144 to 146 in Region 1 versus 144 to 148 in Regions 2 and 3. That's why you hear Europeans working split or listening in odd spots around the band edges. When you operate abroad under a reciprocal arrangement, the local allocation and the local license terms apply, not your home privileges.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.