Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: working out no RX, no TX and SWR protection faults before touching a screwdriver

ci_cover.jpg

Looking for opinions on a sensible order of attack for HF/VHF rigs that arrive on the bench with a vague complaint like "it's dead", "it receives but won't transmit" or "it drops power straight away". The most common mistake is jumping to alignment or finals when the fault is a supply, a connector or a relay. Here is the order I think makes sense, and I'd like to hear where you'd change it.

Start with power, measured where the radio actually sees it. Check the voltage at the radio's DC connector, not at the supply terminals, then watch it while the rig transmits. A supply that reads 13.8 V unloaded and sags to 11 V on transmit points to a bad cable, a corroded fuse holder, a tired electrolytic or a marginal supply. Check the fuses in the radio's own DC lead too. A blown fuse alongside a shorted reverse-polarity diode tells you the previous owner may have crossed the leads. A scope on the supply rails also catches ripple that a meter will average away, and that ripple often turns up later as hum or a noisy receiver.

For no receive, decide whether the problem is before or after the detector. Turn the volume and squelch up and listen for noise. Some noise means the AF chain is alive and the fault is further forward. Then inject a signal. A signal generator on the antenna jack tells you a lot, and even a known local signal helps. Dead on every band suggests a common-path fault such as the antenna relay, a failed first-stage device, a missing local oscillator or a bad IF filter. One band dead suggests band-switching diodes or a bandpass filter. A scope or RF probe on the local oscillator is useful here, because a PLL that never locks looks like a dead receiver but is a different job entirely. Also check any attenuator or preamp switching before you condemn a stage.

For no transmit, break it down. Does the rig key up? Does the TX relay click? Is there drive from the exciter into the driver? Is bias present on the driver and finals? Always do this into a dummy load, and ideally from a current-limited supply. If the radio shows no output on a dummy load, the fault is inside the radio. If it works on the dummy load but folds back on the antenna, you may have a real mismatch such as a bad coax connector, a tuner problem or an antenna fault, not a radio problem.

SWR protection faults need care. If the protection trips on a known-good dummy load, suspect the forward/reflected detector, its diodes, balance trimmer, the sensing resistors or a dirty relay contact feeding bad readings to the control circuit. Don't defeat protection to "see if it transmits" unless you have a dummy load and a plan. If the finals are already damaged, removing protection is how they get destroyed again.

When the finals are blown, find out why before fitting new ones. Common causes are high SWR without working protection, a bias fault, a failed driver, parasitic oscillation after a failed bypass capacitor or a changed component, or overvoltage. Check the bias network, gate resistors, the regulators feeding it and any surrounding diodes and chokes. Replace push-pull devices as a matched pair if the manual says so, set bias to minimum before power-up, and bring the supply up gradually while watching current.

On capacitors, electrolytics are the usual casualties in older gear, but replacing every cap on sight is not a plan. An ESR meter or an in-circuit check shows which ones have actually failed. Match capacitance, voltage rating, temperature rating and polarity, and use low-ESR types in switching supplies. Be more cautious with ceramics in RF, oscillator and filter circuits, where dielectric type and tolerance matter. Leaking SMD electrolytics can eat traces, so clean the board thoroughly and inspect the tracks beneath.

For switches, pots and connectors, use a cleaner that is appropriate for the material, apply it sparingly and work the control through its travel. Isopropyl alcohol is fine for flux and grime but not a cure for every oxidized contact. Also reseat or inspect ribbon cables, board-to-board connectors, shield fingers and RF coax jumpers, because intermittent faults often live there.

I'd leave alignment until last. It's needed after repairs that touch tuned circuits, filters or oscillators, or when the manual's checks show specific parameters out of tolerance. Mark or record original positions, use proper non-metallic alignment tools and follow the service manual's sequence. A manual with the block diagram, test points and alignment table can save more time than any one instrument.

Where do you draw the line between "worth chasing" and "parts unit", and which test gear gets the most use on your bench?

  • Replies 2
  • Views 52
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put one thing ahead of most of that: look at the radio before powering it. Check for a cracked solder joint at the DC jack, corroded battery or fuse contacts, heat-discoloured resistors, bulging caps and any previous repair work. It takes a couple of minutes and spares you from applying power to something with an obvious short.

On test gear, a decent DMM with a diode range and a current clamp or in-line current measurement covers a surprising number of faults. A scope becomes valuable when you need to see something change over time: PLL control voltage, oscillator startup, supply ripple, audio clipping or a PTT line chattering. Keep the ground lead short. Long probe grounds on RF circuits can mislead you badly. If the unit has an off-line power supply, don't connect a grounded scope to it without an isolation transformer or a clear understanding of what the chassis is tied to.

For intermittent faults, tapping with a plastic tool and gentle flexing of the board while monitoring a key voltage is often more productive than reaching for the soldering iron.

  • Administrators

On blown finals, I'd be strict about the dummy load and the first power-up. Replacement devices can die in a fraction of a second if the bias is wrong or the stage is oscillating. A bench supply with a current limit, a wattmeter and a bias set to the manual's idle current gives you a chance to catch problems before the new parts do.

One caveat on SWR protection: a radio that shows high SWR on a dummy load may not have a detector fault. A dummy load that is not truly 50 ohms at the test frequency, a bad adapter, or a poorly seated connector can all cause it. Test with a known-good load and a short jumper first, then look at the sensing circuit.

On noise, don't blame the radio until you check the external environment. Switch-mode supplies, LED lighting and poor grounding can produce noise that looks like a failing receiver. Running the rig from a linear supply or battery is a quick way to separate a radio fault from a noise source in the shack. If the noise stays with the radio on battery with the antenna removed and a dummy load connected, then start looking at internal causes, such as dried-out filter caps or a bad regulator.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.