Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bring-up order for a first homebrew QRP transmitter: what to check before you key it into an antenna

ci_cover.jpg

A lot of first-time builds, whether a Pixie, a Tuna Tin 2 style crystal rig, a BITX board or a uBITX, work on the bench and still fail when they meet an antenna. The usual causes are an oscillator off frequency, a PA running into a bad load, or harmonics that nobody measured. A fixed bring-up order catches most of these. Here is a proposed order. Please poke holes in it.

1. Power first, with a current limit. If your supply has a current limit, set it just above the expected draw. A Pixie-style rig is tens of milliamps on receive, and a QRP CW stage may draw a few hundred milliamps on key-down. If your supply has no limit, put a 10 to 47 ohm resistor in series for the first power-up and watch the voltage drop. Check the polarity and the regulator output before the ICs or the Si5351 module are connected to the rail. A reverse-polarity diode or a fuse is cheap insurance.

2. DC checks before RF. Measure the bias on each transistor stage. Check that the supply reaches the oscillator, driver and PA, and look for shorts to ground on the output side. In a class-C or class-E style PA, the collector DC voltage should be close to the supply voltage with the key up. In a linear stage, check the bias against the schematic.

3. Prove the oscillator by itself. Before the PA is connected, check the oscillator frequency with a counter, or with a receiver or SDR on a short pickup wire. Crystal oscillators can sit on the wrong overtone or a spur, and a VXO can pull to the edge of its range. For a Si5351-based rig, confirm that the calibration offset is set. If the dial reads 7.030 MHz and the output is somewhere else, you will find out later at the worst time.

4. Always use a dummy load first. A 50 ohm non-inductive load is a basic piece of test gear. For a few watts, several 150 ohm metal-film resistors in parallel (three give 50 ohm) work for short key-downs, but check the power rating and keep the keying short. Measure the output with an RF probe on a DMM or a scope. Power is P = Vrms² / R, and Vrms = Vpp / (2√2). At 50 ohms, 10 Vpp is about 250 mW and 20 Vpp is 1 W. Use a 10:1 scope probe and keep the ground lead short, or the waveform will mislead you.

5. Look at the spectrum, not just the power. A rig that makes 1 W of RF at the right frequency can also be putting out a strong second or third harmonic. The cheapest spectrum check is an SDR or a general-coverage receiver, with attenuation between the transmitter and the receiver (a 30 to 60 dB attenuator pad or a resistive tap is safer than a pickup wire). The numbers are only relative, but they show whether the harmonics are far down or close to the fundamental. Ideally, measure at the output of the low-pass filter, not before it.

6. Low-pass filter, built carefully. A typical QRP filter is a 5-element or 7-element Chebyshev or elliptic filter for the band. With toroids, the inductance depends on the turns count squared (L = AL × N²), so one turn more or less matters. For a T37-6, AL is about 3.0 nH per turn squared, so roughly 19 turns gives 1.1 µH. Measure the finished coil if you have an LC meter or a NanoVNA. Use capacitors with a decent tolerance, and check the filter on a VNA if you can. If the filter's cutoff sits too low or too high, the fundamental gets attenuated or the harmonics are not removed.

7. SWR bridge before the antenna. Check the transmitter into the dummy load, then through the SWR bridge, then into the antenna. If the reflected reading with a good dummy load is not close to zero, calibrate or fix the bridge before using it as a reference.

8. Keying and receive behavior last. Check key clicks (the keying envelope should have a rise and fall time of a few milliseconds), then check that the receive path recovers cleanly after transmit. In a Pixie-style or BITX-style rig that shares stages between transmit and receive, T/R switching problems often show up here as thumps, hum, or a dead receiver.

What would you add or change? For a first build, what is the one piece of test equipment you would buy before anything else: a NanoVNA, a scope, or a frequency counter?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The order is good. I would move the harmonic check earlier for anything with a Si5351. Those outputs are square waves, so the unfiltered output is full of odd harmonics, and the amount depends on the stages after the clock. A rig can look fine on a power meter and still be loud on three times the frequency. If you only have one instrument for that stage, an SDR with a proper attenuator is more useful than a scope.

On the first piece of test gear: a NanoVNA is good value, but it will not replace a dummy load. Check the load itself on the VNA, too. A homemade resistor load can look fine at 7 MHz and drift badly on 20 or 15 m because of lead inductance.

  • Moderators

One thing I would add to step 4 is an indicator for how long the dummy load was keyed. Resistors of 0.25 W each do not survive continuous carrier at 1 to 2 W, and a load that is slowly changing value gives you false SWR readings. A pulse of key-down at a time is fine for checking, and a metal oxide or a proper dummy load is better for longer tuning.

For a first build, I would also separate the question of kit versus scratch build. With a kit like the uBITX, the main risks are solder bridges on the small parts and untested modules, and the bring-up order above still applies. For a Pixie or a Tuna Tin 2 style circuit, the circuit is simple enough that the problems are usually the crystal, the toroid winding or a wrong component value. Is the OP planning a kit or a design from an article?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.